> TSM's
>
> I know there's a lot of work being done on connecting 3575 ATL's
thru an
> IBM SAN Data Gateway so there's a good chance someone else
(besides me)
> has had the following connection problem:
>
> After connecting the 3575L12 to the SAN Data Gateway all scsi
devices
> (/dev/rmt0 /dev/rmt1 /dev/smc0) become visible to AIX as scsi
(fcp)
> devices, but when doing a read test on any of the drives it
responds
> with a device not ready, errno 46. Opening the drive and querying
it's
> status does not return an error, only when trying to physically do
> something to a tape in the drive causes a drive shutdown: device
not
> ready. The robot (/dev/smc0) is working fine, using tapeutil tapes
> can be shuffled around without a problem.
>
> I've made sure that the very latest on software is installed on
AIX
> (4.3.3 with IY05369, ATAPE 5.1.4.2) and the Gateway (03.41.27).
The 3570
> drives are at microcode level 5424.
>
> Anybody have a clue ?
>
>
>
> ______________________________ Reply Separator
_________________________________
> Subject: Rename NT Server Service
> Author: "ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU> at INET-1
> Date: 11/30/00 10:57 PM
>
>
> Hello,
>
> Renaming the NT server services is not recommended.
>
> The server initialization wizard creates up to four instances of the
server
> and names the services:
>
> TSM Server1
> TSM Server2
> TSM Server3
> TSM Server4
>
> The server utilities depends on these names for certain operations. If
> you rename them then the server will work but the wizards and other
> features of the server utilities will not work properly with the renamed
> service.
>
> If you must rename the services for some reason then it is better to use
> remove.exe and install.exe that are located in the ...\tivoli\tsm\utils
> directory. You can run each with no arguments to get a usage message. The
> majority of the dsmcutil parameters do not apply to the server and you
will
> have difficulty specifying the service location doing it that way.
>
>
> Date: Thu, 30 Nov 2000 16:52:47 -0500
> From: Steve Firmes <steve.firmes AT ARTICULENT DOT COM>
> Subject: Rename NT Server Service
>
> Does anyone know how to change the NT Service for the TSM Server? I
> used
> the 4.1 wizard and the service was created as "Server 1". I would like
> to
> rename/delete and recreate it with a more appropriate name.
>
> TIA
>
> Stephen Firmes, Storage Management Specialist
> Articulent Inc.
> 45 South Street, Hopkinton, MA 01748
> P: 508-497-2500/F: 508-497-3464
>
> Please visit our web site at www.articulent.com
>
> ------------------------------
>
> Date: Thu, 30 Nov 2000 16:38:40 -0600
> From: Rob Schroeder <robs AT FAMOUSFOOTWEAR DOT COM>
> Subject: Re: Rename NT Server Service
>
> For NT
>
> go to the location of the backup client (i.e. c:\program
> files\tivoli\tsm\baclient)
>
> run the command dsmcutil remove /name:"server 1"
>
> then run dsmcutil install /name......with all the required
> parameters, the
> parameter list is availble in the online help of the application
>
> Regards,
>
> Mike Collins
> Tivoli Storage Manager Development
>
>
> -----------------------------------------------------------------
> ATTENTION:
> The information in this electronic mail message is private and
> confidential, and only intended for the addressee. Should you
> receive this message by mistake, you are hereby notified that
> any disclosure, reproduction, distribution or use of this
> message is strictly prohibited. Please inform the sender by
> reply transmission and delete the message without copying or
> opening it.
>
> Messages and attachments are scanned for all viruses known.
> If this message contains password-protected attachments, the
> files have NOT been scanned for viruses by the ING mail domain.
> Always scan attachments before opening them.
> -----------------------------------------------------------------
|
