Author: "Campbell, Rose" <campbelr AT JNTF.OSD DOT MIL>
Date: Mon, 24 Aug 1998 09:13:59 -0600
Hi all, I have a Data General Aviion with a Clariion 3000 - 30 disk raid array connected to an IBM 3575 - L12, which we just upgraded to an L18 on Friday. The problem is when I try to check the new t
Author: James SPORER <james.sporer AT CCMAIL.ADP.WISC DOT EDU>
Date: Mon, 24 Aug 1998 11:03:15 -0600
The volumes need to be labeled before you can check them in. Hi all, I have a Data General Aviion with a Clariion 3000 - 30 disk raid array connected to an IBM 3575 - L12, which we just upgraded to a
Author: "Campbell, Rose" <campbelr AT JNTF.OSD DOT MIL>
Date: Mon, 24 Aug 1998 10:24:45 -0600
The tapes are already labeled with barcode. Is there something special I have to do so that ADSM knows this? I didn't have to do anything with the first tapes. By the way this is ADSM on NT4.0. Rose
ADSM doesn't have to know anything about the barcode - only the robot cares about that. What ADSM needs is for the label to exist on the media itself, which is not the case now. Run dsmlabel. Richar
Author: "Campbell, Rose" <campbelr AT JNTF.OSD DOT MIL>
Date: Mon, 24 Aug 1998 13:07:42 -0600
Thank you for the information, however, after I initiate that command I am getting the following error. ANR9752E Could not access drive mt1.0.0.1. It may be in use by another application. There are n
Do a 'SHOW LIBRARY' to see what ADSM thinks of the current state of the library and its drives. Check the physical state of the drives by visual inspection, operating system query commands, and what
Author: James SPORER <james.sporer AT CCMAIL.ADP.WISC DOT EDU>
Date: Mon, 24 Aug 1998 15:51:14 -0600
If you have version 3 of the adsm server, you can use the label command from a command line prompt to put an internal label on the tapes, rather than using dsmlabel. Jim Thank you for the information
Checking in tapes in the 3575 is slightly different than checking in a tape on a 3494 library. If you are at v3 you don't have to do the dsmlabel command, you can label your tape and check it in at t
Rose, Did you format the tapes first ? I have the same problem with my MagStar 3570 which uses the same tapeunit drives. If you format the tapes, you can try to use the LABEL LIBV command within ADSM
Author: "Campbell, Rose" <campbelr AT JNTF.OSD DOT MIL>
Date: Tue, 25 Aug 1998 14:29:34 -0600
Johan, I think I have the same library a 3575 with MagStar 3570 drives. I figured out the easiest way to get the tapes labeled is to do it through the wizard (this is on an NT server). I am in the pr
Author: Brenda Burns <Brenda_J_Burns AT DLC.DQE DOT COM>
Date: Tue, 25 Aug 1998 16:50:06 -0400
I have completed this process several times in the past few months on a 9710 library with DLT tapes. Load the tapes into your Silo, issue: AUDIT LIBRARY libname CHECKLABEL=BARCODE After the audit is
Author: Peter Gathercole <peter.gathercole AT VIRGIN DOT NET>
Date: Fri, 28 Aug 1998 00:05:45 +0100
Did you label the tapes? 3575 tapes do not come with ADSM labels written on the tapes. Use the "dsmlabel" command. I think that the full command should be "dsmlabel drive=/dev/rmt0 library=/dev/smc0
Author: Jason Morgan <jason-m AT JASON-M.DEMON.CO DOT UK>
Date: Sun, 30 Aug 1998 13:24:15 +0100
We use the following dsmlabel -drive=/dev/rmt2,16 -drive=/dev/rmtt3,17 -library=/dev/smc1 -search -barcode followed by checkin libv 3575lib search=yes status=scratch checkl=barcode Hope this helps Ja