- 1. Re: DLT7000 (score: 1)
- Author: johnma <johnma AT SLEWPY.DRF DOT COM>
- Date: Tue, 20 Oct 1998 17:32:05 -0400
- for manual tape library, how do you tell adsm to use a specific tape drive with your backup administrative commands. I have four tapes drives, two dlt2000 and two dlt7000. JohnMa. johnma AT drf DOT
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-10/msg00786.html (9,999 bytes)
- 2. Re: DLT7000 (score: 1)
- Author: "Prather, Wanda" <PrathW1 AT CENTRAL.SSD.JHUAPL DOT EDU>
- Date: Wed, 21 Oct 1998 14:39:47 -0400
- I don't think there is any way to do that, if all the drives are the same device class. However, if you are running ADSM V3, I think there is a command to vary offline the tape drive you DON"T want t
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-10/msg00815.html (10,704 bytes)
- 3. DLT7000 (score: 1)
- Author: Felipe Bagkus <fbagkus AT SKILLSET DOT COM>
- Date: Tue, 22 Sep 1998 15:45:09 -0700
- I have the fortunate task of implementing the ADSM in our company using Quantum DLT7000 in a WinNT and Lotus environment. And right off the bat I ran into trouble. The device configuration wizard acc
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-09/msg00998.html (11,495 bytes)
- 4. Re: DLT7000 (score: 1)
- Author: "Kelly J. Lipp" <lipp AT STORSOL DOT COM>
- Date: Tue, 22 Sep 1998 21:19:49 -0600
- Your problem is with the define devclass command. You should use: define devclass dlt devtype=dlt format=35c library=libname Delete the devclass you have and redefine using the above and you should b
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-09/msg01006.html (10,585 bytes)
- 5. DLT7000 (score: 1)
- Author: Felipe Bagkus [SMTP:fbagkus AT SKILLSET DOT COM]
- Date: Sun, 04 Oct 2015 17:53:22 -0500
- I have the fortunate task of implementing the ADSM in our company using Quantum DLT7000 in a WinNT and Lotus environment. And right off the bat I ran into trouble. The device configuration wizard acc
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-09/msg01007.html (11,558 bytes)
- 6. Re: DLT7000 (score: 1)
- Author: "Boireau, Eric (MED)" <BOIREER AT EUROMSX.GEMSE DOT FR>
- Date: Wed, 23 Sep 1998 09:36:47 +0200
- You should also start adsmscsi driver to access to your DLT drive. Don't load any other NT drivers about DLT drive Eric
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-09/msg01013.html (13,023 bytes)
- 7. Re: DLT7000 (score: 1)
- Author: Claudia Masters <cmaster1 AT TUELECTRIC DOT COM>
- Date: Thu, 24 Sep 1998 15:30:38 -0500
- Would you get different compression results using: define devclass dlt devtype=dlt format=drive library=libname The doc sounds like ADSM handles the compression with format=drive and hardware compres
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-09/msg01131.html (11,157 bytes)
- 8. Re: DLT7000 (score: 1)
- Author: "Kelly J. Lipp" <lipp AT STORSOL DOT COM>
- Date: Thu, 24 Sep 1998 15:04:09 -0600
- It turns out if the drive firmware is back revved, it might not write at the highest compression possible with format=drive. I've seen this happen at a couple of sites. I've gotten in the habit of sp
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-09/msg01133.html (10,690 bytes)
- 9. Re: DLT7000 (score: 1)
- Author: Claudia Masters [SMTP:cmaster1 AT TUELECTRIC DOT COM]
- Date: Sun, 04 Oct 2015 17:53:22 -0500
- Would you get different compression results using: define devclass dlt devtype=dlt format=drive library=libname The doc sounds like ADSM handles the compression with format=drive and hardware compres
- /usr/local/webapp/mharc-adsm.org/html/ADSM-L/1998-09/msg01134.html (11,188 bytes)
This search system is powered by
Namazu