Veritas-bu

[Veritas-bu] DLT Format Issues

2007-05-02 15:41:26
Subject: [Veritas-bu] DLT Format Issues
From: keith at cydonia.net (Keith W)
Date: Wed, 2 May 2007 12:41:26 -0700 (PDT)
Thank you.
I've contacted a degauss company that will do all of the DLT's for 3.00
each. Given the cost of buying a degausser, this seems very reasonable I
would think.

Thanks again.

+-----------------------+
+       Keith           +
+-----------------------+

On Wed, 2 May 2007 Richard.Mickle at mwrms.rrd.com wrote:

> Keith,
> 
> You can just erase them as stated below, but there is one thing to 
> consider.  The performance you get out of the tape will depend on the type 
> of drive that the tape was used in first.  A DLT2000 tape drive had a 
> different segment size (or is it fragment size?) then a DLT8000.  Also, a 
> VSTape formatted tape can not be used in a DLTx000 drive. 
> 
> I found that the tapes formatted by an older drive could take about twice 
> as long to read and write to.  The end result is if you degauss the tapes, 
> they will be formatted by your current drive, and you should get the best 
> performance out of the tapes.
> 
> 
> Message: 10
> Date: Mon, 30 Apr 2007 16:42:00 -0400
> From: "Justin Piszcz" <jpiszcz.backup at gmail.com>
> Subject: Re: [Veritas-bu] DLT Format Issues
> To: "Keith W" <keith at cydonia.net>
> Cc: Veritas List <veritas-bu at mailman.eng.auburn.edu>
> Message-ID:
>  <8cf000000704301342h7965c336l2d87b329a324eb89 at mail.gmail.com>
> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
> 
> You should be able to check off the overwrite options in NBU though
> and that should take care of it.
> 
> On 4/30/07, Justin Piszcz <jpiszcz.backup at gmail.com> wrote:
> > I'd go for the erase, depends on the DLT version perhaps(?) but for
> > LTO-X tapes, they say right on the package NOT to degauss as a measure
> > of erasure.
> >
> > On 4/27/07, Keith W <keith at cydonia.net> wrote:
> > > I have a hundred or so DLT IV tapes that were in a different/unknown
> > > tape stacker. I need to get them cleaned up so that my Overland 
> machine
> > > will properly see them. Will a simple erase (mt -f /dev/st0 erase) 
> clean
> > > them up enough to be seen by the newer DLT tape machine or do I need 
> to
> > > have them degaused?
> > >
> > > +-----------------------+
> > > +       Keith           +
> > > +-----------------------+
> > >
> > > _______________________________________________
> > > Veritas-bu maillist  -  Veritas-bu at mailman.eng.auburn.edu
> > > http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
> > >
> >
> 
> 
> 
> Richard Mickle
> UNIX Systems and Storage Administrator
> Moore Wallace Response Marketing Services
> An RR Donnelley Company
> E-Mail:         Richard.Mickle at mwrms.rrd.com
> Phone:        920-339-1695
> Cell Phone: 920-366-1987
> Fax:             920-339-1807
> 


<Prev in Thread] Current Thread [Next in Thread>