HI,

I use the blat command with specifing the server each time. I run it once with 
the -install option and then I don't supply the server again.

Regards,
Jim Peppas





>  -------Original Message-------
>  From: j. okabayashi <fishnfool AT gmail DOT com>
>  Subject: Re: [Veritas-bu] Setting up Mail Notifications
>  Sent: 17 Nov '05 20:48
>  
>  Thanks Mark. I actually went through and manually straightened it out.
>  The problem I'm having now is that I'm still not getting notifications
>  after following the veritas article. Does anyone else know what needs to
>  be done other than putting the the e-mail server in the following line?
>  
>  
>  @blat %3 -s %2 -t %1 -i NetBackup -server [LINK:
>  http://EMAILSERVER.MYCOMPANY.COM] EMAILSERVER.MYCOMPANY.COM -q
>  
>  
>  I can send email using blat so I know that works. It has to be something
>  in the nbmail file. Any help would be appreciated.
>  
>  
>  Thanks.
>  
>  Jason
>  
>  
>  On 11/17/05, [LINK: MAILTO:MARK.DONALDSON AT CEXP DOT COM]
>  MARK.DONALDSON AT CEXP DOT COM <[LINK: mailto:Mark.Donaldson AT cexp DOT com]
>  Mark.Donaldson AT cexp DOT com> wrote:
>  
>  this is probably because of your editor choice.  I think Notepad uses a
>  <CR><LF> for a flat file while Wordpad uses a <CR> only.
>  
>  
>  For DOS to UNIX, I always use Wordpad.  I'm not sure what to do for your
>  situation other than suggest trying a different editor.
>  
>  
>  -M
>  
>  -----Original Message-----
>  FROM: [LINK: mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu]
>  veritas-bu-admin AT mailman.eng.auburn DOT edu  [mailto:[LINK:
>  mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu]
>  veritas-bu-admin AT mailman.eng.auburn DOT edu]ON BEHALF OF j. okabayashi
>  SENT: Wednesday, November 16, 2005 6:41 PM
>  TO: [LINK: mailto:veritas-bu AT mailman.eng.auburn DOT edu]
>  veritas-bu AT mailman.eng.auburn DOT edu
>  SUBJECT: [Veritas-bu] Setting up Mail Notifications
>  
>  
>  Can somebody help be configure BLAT on my Master server? It is NBU 5.1
>  mp3a on W2k3. I followed the directions from the veritas article, but I'm
>  not getting any e-mails. One thing I noticed, after I edited the
>  NBmail.com  file it lost it's "structure" . See below.
>  
>  
>  @REM $Header: nbmail.cmd,v 1.3 2003/06/25 18:07:46 [LINK:
>  mailto:$@REM@REM] $@REM@REM [LINK: mailto:bcpyrght@REM] bcpyrght@REM
>  [LINK:
>  
> mailto:***************************************************************************@REM]
>  
> ***************************************************************************@REM
>  * $VRTScprght: Copyright 1993 - 2004 VERITAS Software Corporation, All
>  Rights Reserved $ [LINK: mailto:*@REM] *@REM  [LINK:
>  
> mailto:***************************************************************************@REM]
>  
> ***************************************************************************@REM
>  [LINK: mailto:ecpyrght@REM]  ecpyrght@REM @REM - - - - - - - - - - - - - -
>  - - - - - - - - - - - - - - - - - - - - - - - [LINK: mailto:-@REM] -@REM -
>  
>  [LINK: mailto:-@REM]  -@REM - HOW TO SEND MAIL FROM THE NT NETBACKUP
>  SERVER                           [LINK: mailto:-@REM] -@REM -
>  [LINK:
>  mailto:-@REM]  -@REM - NetBackup checks if the mail script
>  (NetBackup\Bin\nbmail.cmd) exists.  [LINK: mailto:-@REM] -@REM - If the
>  script exists, NetBackup runs it passing three parameters on     [LINK:
>  mailto:-@REM]  -@REM - the command line:
>  
>  
>  Is this normal? Any help would be appreciated.
>  
>  
>  Thank you,
>  
>  Jason