Hrm..

The WWN/etc do appear in the devlink.tab.

ype=ddi_pseudo;name=sg;addr=7e,1;      sg/c\N0t126l1
type=ddi_pseudo;name=sg;addr=w2100000c500187f5,0;       sg/c\N0t\A1l0
type=ddi_pseudo;name=sg;addr=w2100000c500187f5,1;       sg/c\N0t\A1l1
type=ddi_pseudo;name=sg;addr=w2100000c50018daa,0;       sg/c\N0t\A1l0
type=ddi_pseudo;name=sg;addr=w2100000c50018daa,1;       sg/c\N0t\A1l1
type=ddi_pseudo;name=sg;addr=w500104f00052cf1f,0;       sg/c\N0t\A1l0
type=ddi_pseudo;name=sg;addr=w500104f00052cf1f,1;       sg/c\N0t\A1l1
type=ddi_pseudo;name=sg;addr=w500104f00052cf22,0;       sg/c\N0t\A1l0
type=ddi_pseudo;name=sg;addr=w500104f00052cf22,1;       sg/c\N0t\A1l1
# end SCSA devlinks

I will check the sg/st configuration correspondence.

Thanks,
Justin.

-----Original Message-----
From: Paul Gimpelev [mailto:paulg AT CDCNA DOT COM] 
Sent: Wednesday, September 07, 2005 2:51 PM
To: Piszcz, Justin; veritas-bu AT mailman.eng.auburn DOT edu
Subject: Re: [Veritas-bu] Brocade + Solaris 10 - I see devices with
cfgadm -alv, but not sgscan(?)

Justin,

        There are a few things you can look at.  Most likely, it is a
problem
with /etc/devlink.tab, it has missing sg entries.  It needs to contain
the
entries for the devices that correspond to the target/lun of what you
have on
your tape drives.  The file is rather ugly, the entry should look like
this for
target 19, lun 8:

type=ddi_pseudo;name=sg;addr=13,8;      sg/c\N0t19l8

Once you are done, you will need to either unload the sg module or
reboot and
then re-run sgscan.
Also, check the contents of your sg.conf file and make sure they
correspond to
your st.conf.  Another suggestion is to make sure in st.conf your tape
drives
are persistently bound.

paulg

On Sep 7,  2:22pm, Piszcz, Justin wrote:
> Subject: [Veritas-bu] Brocade + Solaris 10 - I see devices with cfgadm
-al
>
> I have a problem
>
>
>
> I am getting closer to configuring Brocade & the Sun Dual Fiber 2342
HBA
> Card.
>
> Now my problem is, I cannot get sgscan to see the devices.
>
>
>
> root@backup01-dev# cfgadm -alv | grep HP
>
> c3::500104f00052cf1f           connected    configured   unknown    HP
> Ultrium 2-SCSI
>
> c3::500104f00052cf22           connected    configured   unknown    HP
> Ultrium 2-SCSI
>
> root@backup01-dev#
>
>
>
> root@backup01-dev# sgscan -v -v
>
> root@backup01-dev#
>
>
>
> The devices *ARE* seen by Solaris however!
>
>
>
> ot@backup01-dev# ls /dev/rmt
>
> 0     0cb   0hb   0lb   0mb   0u    1     1cb   1hb   1lb   1mb   1u
>
> 0b    0cbn  0hbn  0lbn  0mbn  0ub   1b    1cbn  1hbn  1lbn  1mbn  1ub
>
> 0bn   0cn   0hn   0ln   0mn   0ubn  1bn   1cn   1hn   1ln   1mn   1ubn
>
> 0c    0h    0l    0m    0n    0un   1c    1h    1l    1m    1n    1un
>
> root@backup01-dev#
>
>
>
> I have re-run my configuration script but it is not working.
>
>
>
> rem_drv sg &&   /usr/bin/rm -f /kernel/drv/sg.conf &&
> /usr/openv/volmgr/bin/driver/sg.install && cd
> /usr/openv/volmgr/bin/driver && /usr/openv/volmgr/bin/sg.build all -mt
> 126 -ml 1 && sgscan tape
>
>
>
>
>
> Does anyone have any suggestions?
>
>
>
> Thanks,
>
>
>
> Justin.
>
>
>
>
> [ Attachment (text/x-html): 7349 bytes
>   Character set: us-ascii
>   Encoded with "quoted-printable" ]
>-- End of excerpt from Piszcz, Justin