Jeff,
I am having the same problem:
I am using NBU 4.5 on Solaris8 and I followed the device manger guide. When
I run the sgscan command I got this error:
Tape device types enabled in the Solaris tape driver, st(7D), configuration
file: QUANTUM DLT7000:
dev/sg/c3t4l0: Tape (/dev/rmt/0): "COMPAQ DLT7000 011A" :
NOT-IN-ST-CONFIG-FILE
================= TPCONFIG -D ===================
Index DriveName DrivePath Type Shared Status
***** ********* ********** **** ****** ******
0 COMPAQDLT70000 /dev/rmt/0cbn dlt2 No UP
===================== SCAN ======================
************************************************************
*********************** SDT_TAPE ************************
*********************** SDT_CHANGER ************************
*********************** SDT_OPTICAL ************************
************************************************************
------------------------------------------------------------
Device Name : "/dev/rmt/0cbn"
Volume Header: ""
Port: -1; Bus: -1; Target: -1; LUN: -1
Inquiry : "COMPAQ DLT7000 011A"
Vendor ID : "COMPAQ "
Product ID : "DLT7000 "
Product Rev: "011A"
Serial Number: "PXA48P2984"
WWN : ""
WWN Id Type : 0
Device Type : SDT_TAPE
Removable : Yes
Device Supports: SCSI-2
Flags : 0x4
Reason: 0x0
I've checked VERITAS support web and point out to this link:
http://seer.support.veritas.com/docs/239652.htm
But I have the patch 108725-05 and I still can not figur out what is wrong,
Thanks,
Adam
----- Original Message -----
From: "Bill Wiessner" <bill.wiessner AT veritas DOT com>
To: "'Jeff Kennedy'" <jlkennedy AT amcc DOT com>; "NBU List"
<veritas-bu AT mailman.eng.auburn DOT edu>
Sent: Tuesday, July 23, 2002 12:14 PM
Subject: RE: [Veritas-bu] st.conf entries for DLT7k
> Jeff,
>
> You don't say which version of NBU you are running...but from the NBU v4.5
> "Media Manager Device Configuration Guide" pages 18 and 19, VERITAS says:
>
>
> "QUANTUM DLT7000", "Quantum DLT7000 Tape Drive", "Q-DLT7000",
>
> Q-DLT7000 = 1,0x38,0,0x19639,4,0x82,0x83,0x84,0x85,3;
>
>
> ________________________________________
>
> Bill Wiessner
> Sr. Staff Systems Engineer
> VERITAS Software Corporation
>
> Office: 410-877-7689
> Cell: 410-804-3321
> mailto:bill.wiessner AT veritas DOT com
> http://www.veritas.com/
>
> ________________________________________
>
> -----Original Message-----
> From: Jeff Kennedy [mailto:jlkennedy AT amcc DOT com]
> Sent: Tuesday, July 23, 2002 11:58 AM
> To: NBU List
> Subject: [Veritas-bu] st.conf entries for DLT7k
>
> I am getting conflicting stories on what should go in st.conf for the
> DLT 7k.
>
> ATL says the following:
>
> tape-config-list=
> "QUANTUM DLT7000", "DLT 7000", "DLT7000",
> DLT7000 = 1,0x38,0,0x8639,4,0x82,0x83,0x84,0x85,3;
>
> However, Sun says the following:
>
> tape-config-list=
> "QUANTUM DLT7000", "QUANTUM DLT7000", "DLT7k-data";
> DLT7k-data = 1,0x36,0,0x1D639,4,0x82,0x83,0x84,0x85,2;
>
> And the main reason I post this is that with ATL's entry for DLT7k I get
> unexpected token errors from st.conf. Funny thing though, the SDLT
> entry is fine.
>
> Can anyone verify a Solaris st.conf dlt7k entry for an ATL library for
> me?
>
> Thanks.
> --
> =====================
> Jeff Kennedy
> Unix Administrator
> AMCC
> jlkennedy AT amcc DOT com
> _______________________________________________
> Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
> http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
> _______________________________________________
> Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
> http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
>
|