Hi Srini,
1. Are the tape libraries connected via SCSI or fibre channel?
2. Can you access the tape drives using the "mt" command to prove connection
to them (e.g. mt -f /dev/rmt/1cbn status)?
3. Are the tape libraries closed and online? "Device Busy" from a tape
library often means that the tape library isn't talking to the SCSI bus
because it has been put offline.
Good luck!
Mark
> I am getting these errors for both of these as follows :
> # ./sjirjc [email protected]
> SJIRJC: Device busy
> Code:0x29, Str=<I/O error>
> # ./sjirjc [email protected]
> SJIRJC: Device busy
> Code:0x29, Str=<I/O error>
>
> This jukebox was always attached but I am not sure if it was working.
>
> Here is the pkginfo
>
> # pkginfo | grep LGT
> application LGTOclnt NetWorker for Solaris (Backup/Recover) Client
> system LGTOdrvr NetWorker for Solaris (Backup/Recover) Device
> Drivers
> application LGTOman NetWorker for Solaris (Backup/Recover) Man
> application LGTOnode NetWorker for Solaris (Backup/Recover) Storage Node
> application LGTOserv NetWorker for Solaris (Backup/Recover) Server
<snip>
>
>
> -----Original Message-----
> From: Carston Locher [mailto:clocher AT LEGATO DOT COM]
> Sent: Tuesday, February 25, 2003 10:49 AM
> To: NETWORKER AT LISTMAIL.TEMPLE DOT EDU
> Subject: Re: [Networker] Jukebix configuration problem in 5.5.3
>
>
> Srini,
>
> You should do the following:
>
> 1) run the command: inquire (/etc/LGTOuscsi/inquire)
> 2) run the command: sjirjc <scsi_address_of_robotics>
> (such as: sjirjc [email protected]) (for both jukeboxes)
>
> Please send the output to this mailing list. Is this a new install?
> Has either jukebox ever worked with NetWorker?
>
> What is the output of "pkginfo | grep LGT"? Are there any errors in
> /var/adm/messages?
>
> Thanks,
>
> Carston
>
> On Tue, 2003-02-25 at 10:36, Srini Bala wrote:
>> We didthat in that order. The error message keep saying te driver
>> installation seems incorrect. i removed all the packages and added them again
>> (the whole set).
>> Does anyone know of any problems with the drivers for solaris 7, do we need
>> any patches or anything like that?
>> We have the storedge L280 with HP tapelibrary (C6280-7000)
>> I will check out the dip switches as well.
>> thnaks
>> -Srini
>>
>> -----Original Message-----
>> From: Kevin [mailto:kbernard10 AT COGECO DOT CA]
>> Sent: Monday, February 24, 2003 7:37 PM
>> To: NETWORKER AT LISTMAIL.TEMPLE DOT EDU
>> Subject: Re: [Networker] Jukebix configuration problem in 5.5.3
>>
>>
>> In order to configure the autochanger, the following packages must be
>> installed
>> in the right order:
>>
>> 1) client package
>> 2) drivers package
>> 3) storage node package
>>
>> If you are using this machine as a server, then the server package is
>> installed after
>> the storage node.
>>
>> Also, what type of autochanger is it? If it is an HP 1557 or similar, it
>> may require
>> dip switches on the bottom to be changed.
>>
>> Hope this helps,
>> Kevin
>>
>> At 04:39 PM 2/24/2003 -0800, you wrote:
>>> Hello,
>>> We have Legato Networker 5.5.3 running on solaris 7. We have 2
>>> autochangers attached to it alongwith 1 tapedrive each. We are getting the
>>> following message when trying to configure it using jb_config :
>>> # jb_config
>>> 1) Install a SmartMedia Jukebox.
>>> 2) Install an Autodetected SCSI Jukebox.
>>> 3) Install an SJI Jukebox.
>>> 4) Install an RLM Jukebox.
>>> 5) Install an STL Silo.
>>>
>>> What kind of Jukebox are you installing? [1] 2
>>> These are the SCSI Jukeboxes currently attached to your system:
>>> 1) [email protected]: Standard SCSI Jukebox, Vendor <HP>, Product <C6280-7000>
>>> 2) [email protected]: Standard SCSI Jukebox, Vendor <HP>, Product <C6280-7000>
>>> Which one do you want to install? 2
>>> Installing an 'Standard SCSI Jukebox' jukebox.
>>> Name you would like to assign to the jukebox device? tape_library_2
>>> Pathname of the control port for the jukebox device? [[email protected]]
>>> Unable to access device "Standard SCSI Jukebox" on control port
>>> "[email protected]".
>>>
>>> Have you already installed the "drivers" package on this machine? (yes/no)
>>> no
>>>
>>> You must install the LUS SCSI passthrough driver before configuring
>>> a SCSI jukebox with this program.
>>>
>>> When we tried to answer 'yes' to the drivers questions we get the
>>> following message :
>>>
>>> # jb_config
>>> 1) Install a SmartMedia Jukebox.
>>> 2) Install an Autodetected SCSI Jukebox.
>>> 3) Install an SJI Jukebox.
>>> 4) Install an RLM Jukebox.
>>> 5) Install an STL Silo.
>>>
>>> What kind of Jukebox are you installing? [1] 2
>>> These are the SCSI Jukeboxes currently attached to your system:
>>> 1) [email protected]: Standard SCSI Jukebox, Vendor <HP>, Product <C6280-7000>
>>> 2) [email protected]: Standard SCSI Jukebox, Vendor <HP>, Product <C6280-7000>
>>> Which one do you want to install? 1
>>> Installing an 'Standard SCSI Jukebox' jukebox.
>>> Name you would like to assign to the jukebox device? tape_library_1
>>> Pathname of the control port for the jukebox device? [[email protected]]
>>> Unable to access device "Standard SCSI Jukebox" on control port
>>> "[email protected]".
>>>
>>> Have you already installed the "drivers" package on this machine? (yes/no)
>>> yes
>>> There appears to be something incorrect about your driver
>>> installation. Please consult your driver documentation
>>> to help you troubleshoot your installation.
>>>
>>>
>>> Any idea as to how to troubleshoot this problem?
>>>
>>> Thanks in advance?
>>>
>>>
>>> -Srini
<snip>
--
Note: To sign off this list, send a "signoff networker" command via email
to listserv AT listmail.temple DOT edu or visit the list's Web site at
http://listmail.temple.edu/archives/networker.html where you can
also view and post messages to the list.
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=
|
