You need to run q pr from the TSM interface to see processes.

Jane.


-----Original Message-----
From: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] On Behalf Of
ashish sharma
Sent: 11 February 2009 16:02
To: ADSM-L AT VM.MARIST DOT EDU
Subject: Re: [ADSM-L] cannot run command

Hello,

The o/p of command is as below:


# /usr/sbin/lsdev  -C  -c tape  -H
name  status    location     description

rmt0  Available 1Z-08-00-0,0 Differential SCSI 4mm Tape Drive
rmt1  Available 31-08-01     IBM 3580 Ultrium Tape Drive (FCP)
smc0  Available 31-08-01     IBM 3584 Library Medium Changer (FCP)
rmt2  Available 31-08-01     IBM 3580 Ultrium Tape Drive (FCP)
rmt3  Available 2U-08-01     IBM 3580 Ultrium Tape Drive (FCP)
rmt6  Available 2d-08-01     IBM 3580 Ultrium Tape Drive (FCP)
rmt4  Available 2U-08-01     IBM 3580 Ultrium Tape Drive (FCP)
rmt5  Available 2U-08-01     IBM 3580 Ultrium Tape Drive (FCP)
rmt7  Available 2d-08-01     IBM 3580 Ultrium Tape Drive (FCP)
smc1  Available 2d-08-01     IBM 3584 Library Medium Changer (FCP)
rmt8  Available 2d-08-01     IBM 3580 Ultrium Tape Drive (FCP)
rmt9  Available 2d-08-01     IBM 3580 Ultrium Tape Drive (FCP)
rmt10 Available 2d-08-01     IBM 3580 Ultrium Tape Drive (FCP)





while o/p of "q proc" does not show anything.



Regards

Ashish



On 2/11/09, Kamran Rao <kamran.rao AT grhosp.on DOT ca> wrote:
>
> As root - run "lsdev -Cc tape" and see if your drives and medium
changer
> are showing up as "available" - if shows up as "defined" then you
might
> have a device problem. You have not mentioned what kind of library and
> also if it is a direct connect as "scsi" or via FC adapter etc etc?
>
>
> Regards,
>
> Kamran Rao
>
> -----Original Message-----
> From: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] On Behalf
Of
> ashish sharma
> Sent: February 11, 2009 10:08 AM
> To: ADSM-L AT VM.MARIST DOT EDU
> Subject: [ADSM-L] cannot run command
>
> Hello all,
>
> My TSM server version is
>
> Storage Management Server for AIX-RS/6000 - Version 5, Release 3,
Level
> 5.0 on AIX.
>
> The issue i am facing is that when i try to give command  like "q
path"
> or "q mount" the command hangs as shown below
>
> *************************
> tsm: TSMLM>q mount
>
> *************************
>
> and does not give any o/p but when i give command like q session, it
> works but again i am unable to cancel any session.Does anybody has any
> idea why is it happening?I think restaring the server might solve the
> problem but at present i am not in favour of it.
>
>
>
>
> --
> Best Regards
> Ashish Sharma
> ST Microelectronics Ltd.
> 919717003853
>



--
Best Regards
Ashish Sharma
ST Microelectronics Ltd.
919717003853


Please check that this email is addressed to you. If not, you should delete it 
immediately as its contents may be confidential and its disclosure, copying or 
distribution unlawful.

C. & J. Clark International Limited takes steps to prevent the transmission of 
electronic viruses but responsibility for screening incoming messages and the 
risk of such transmission lies with the recipient.

C. & J. Clark International Limited Trading as Clarks Registered in England 
number 141015.
Registered office 40 High Street, Street, Somerset. BA16 0EQ. England.

This message has been scanned for viruses by BlackSpider MailControl - 
www.blackspider.com