Re: Export quesion
2004-08-26 19:01:45
Wanda / IBM,
This is an opportunity for an enhancement. I've been bit by that
situation also.
The problem is that an export is a single transaction. Either it fails or
it succeeds. As I write this I'm holding my breath hoping that the last
100 GB of the current _3.7 TB_ export complete without a problem. It
has been running for eight days now and has survived two "dropped tape"
events by our 3583 LTO and is currently writing DLT # 64 in our HP 4/40.
What I would like to see is for the export process to be able to resume at
the end of the last completely filled tape. I don't care if it has to
throw away a partially filled tape. I do care if it has to throw away 64
- or more - full tapes.
As servers and data stores get larger, it just isn't practical to cancel a
process running days or weeks because of a single tape I/O failure.
Just a suggestion.
Tab Trepagnier
TSM Administrator
Laitram, L.L.C.
"Prather, Wanda" <Wanda.Prather AT JHUAPL DOT EDU>
Sent by: "ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>
08/26/2004 01:24 PM
Please respond to "ADSM: Dist Stor Manager"
To: ADSM-L AT VM.MARIST DOT EDU
cc:
Subject: Re: Export quesion
You will have to start the EXPORT from the beginning.
-----Original Message-----
From: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] On Behalf Of
Robert Ouzen
Sent: Wednesday, August 25, 2004 5:53 PM
To: ADSM-L AT VM.MARIST DOT EDU
Subject: Export quesion
Hi to all
Today I ran an export command of a few nodes and during the process after
a
few hours I had an error command in one cartridge (DLT8000) couldn't be
read
successfully and the process was abandonded:
08/25/2004 15:44:57 ANR8944E Hardware or media error on drive SRV4
(/dev/mt4)
(OP=LOCATE, Error Number=5, CC=306, KEY=03,
ASC=11,
ASCQ=00,
SENSE=F0.00.03.00.00.00.BA.16.00.00.F3.38.11.00-
.00.00.00.00.81.0D.90.00.00.44.B6.00.5D.47.6D.,
Description=Drive or media failure). Refer to
Appendix D
in the 'Messages' manual for recommended action.
(SESSION: 3305, PROCESS: 210)
08/25/2004 15:44:57 ANR8359E Media fault detected on DLT volume
000090
in
drive SRV4 (/dev/mt4) of library SCALAR.
(SESSION:
3305,
PROCESS: 210)
08/25/2004 15:45:15 ANR0986I Process 210 for EXPORT NODE running in
the
BACKGROUND processed 504589 items for a total of
24,126,583,819 bytes with a completion state of
FAILURE
at 15:45:15. (SESSION: 3305, PROCESS: 210)
My question is did I need to run the process from the beginning or can I
continue from where it was abandonded after fixing the problem on the
damage
volume (move data...).
Thanks in advance .....
Regards Robert Ouzen
E-mail: rouzen AT univ.haifa.ac DOT il
-------------------------------------------------------------------------
FIGHT BACK AGAINST SPAM!
Download Spam Inspector, the Award Winning Anti-Spam Filter
http://mail.giantcompany.com <http://mail.giantcompany.com/>
|
|
|