ADSM-L

Re: collocated storage pool issue

2003-07-16 09:32:12
Subject: Re: collocated storage pool issue
From: Karel Bos <Karel.Bos AT NUON DOT COM>
To: ADSM-L AT VM.MARIST DOT EDU
Date: Wed, 16 Jul 2003 15:31:44 +0200
Hi,

Issue a q vol <volumename> and see if the output has "Scratch Volume?: Yes"
in it. If this is set to NO the volume remains in the storage pool it was
defined to. If it is set to YES, you have to do an audit vol <volumename>
fix=yes.

Regard.

Karel

> -----Oorspronkelijk bericht-----
> Van: Jacques Butcher [mailto:butcherjw AT ANANZI.CO DOT ZA]
> Verzonden: woensdag 16 juli 2003 14:50
> Aan: ADSM-L AT VM.MARIST DOT EDU
> Onderwerp: Re: collocated storage pool issue
>
>
> I also had an issue with collocation before where the tape
> volumes do not go back to scratch after reclaimation ran.
>  By querying the library volumes it does not say that these
> tapes contains "data" but they are still private.  Querying
> the volumes shows that the tapes are empty.  They are
> however not automatically deleted from the pool they belong
> to.  Did anyone else get this?
>
> On Wed, 16 Jul 2003 12:05:24 +0400
>  Zosimo Noriega <znoriega AT ADNOC DOT COM> wrote:
> > Increase the value of Maximum Scratch Volumes Allowed in
> > new storage pool.
> > You can reorganize client data into new collacted storage
> > pool by moving
> > node data.
> >
> > Regards,
> > Zosi Noriega
> >
> > -----Original Message-----
> > From: Abdulaziz Almuammar [mailto:amuammar AT KFSHRC.EDU DOT SA]
> > Sent: Wednesday, July 16, 2003 9:30 PM
> > To: ADSM-L AT VM.MARIST DOT EDU
> > Subject: collocated storage pool issue
> >
> > Hi guys,
> > I have uncollocated storage pool that stores all the
> > client data in 3494
> > tape library and I created a new collocated storage pool
> > and redirected all
> > new client data to be stored on it.
> > Each tape in the collocated storage pool is supposed to
> > have one node data
> > (if the pool has empty tapes as I know) but what I foud
> > in the new storage
> > pool is different
> > I found that "some" of the nodes data are stored in one
> > tape.
> > Could any one tell me if this is normal? and if it is not
> > how can I force
> > each tape to have one client data?
> >
> > I have TSM 5.1.5 on AIX 4.3.3
> >
> > Regards,
> > Abdulaziz
>
> Jacques Butcher
> TCM (Technology Corporate Management) Software Engineer
> Cell:  +27 (0)84 676 0329
> Tell:  +27 (0)11 483-2000
> Fax:   +27 (0)11 728-3656
> Nat. IT Diploma, MCSE, IBM Tivoli Storage Manager 5.1
> Certified, NetVault Certified, IPSTor Certified,
> IBM Certified Specialist - Enterprise Tape Solutions
> Version 2
>
> ==
> Download ringtones, logos and picture messages at Ananzi Mobile Fun.
> http://www.ananzi.co.za/cgi-bin/goto.pl?mobile
>

<Prev in Thread] Current Thread [Next in Thread>