Hello Humberto
I'll give you my best answer (and hope it helps);
The ANR8302E Says OP=OFFL meaning the drive is offline, you should be able
to see this on the library display. The sense code, comes from the device
(the drive) itself, and is not likely to be wrong (seen from a drive
perspective). It could be, you haven't labelled your volume, or that the
volume should be re-labelled, or checked for errors. Does this happen to all
volumes?
A long time ago, (at least 2 years) I upgraded a 3583 using serial
communication on the back of the library. I can't remember the exact way to
do it, but there is a small text document on the web (IBM), describing how
to do it, both by serial, and by SCSI, and the utilities to use. Try this
link - ftp://ftp.software.ibm.com/storage/358x/3583/3583_Howto.txt
Utilities to use at the same place (i think).
Rgds
Geirr G. Halvorsen
-----Original Message-----
From: Humberto Gómez López [mailto:hugomez AT UCAB.EDU DOT VE]
Sent: 20. februar 2003 14:31
To: ADSM-L AT VM.MARIST DOT EDU
Subject: About LTO 3583
Hi I have two questions
Do anyone know how to solve this issue, after checkin in a tape, I audit the
library and I keep getting this response
ANR8304E Time out error on drive MT0.2.0.3 (\\.\Tape0) in
library LB0.1.0.3.
02/20/2003 09:09:36 ANR8912E Unable to verify the label of volume from
slot-element 4096 in drive MT0.2.0.3 (\\.\Tape0) in
library LB0.1.0.3.
02/20/2003 09:09:36 ANR8302E I/O error on drive MT0.2.0.3 (\\.\Tape0)
(OP=OFFL, Error Number=21, CC=0, KEY=02, ASC=3A,
ASCQ=00,
SENSE=70.00.02.00.00.00.00.1C.00.00.00.00.3A.00.00.00.10-
.13.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.04.0-
0.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.-
00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00-
.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.0-
0.00.00.00.00, Description=An undetermined error has
occurred). Refer to Appendix D in the 'Messages'
manual
for recommended action.
02/20/2003 09:09:37 ANR8942E Could not move volume NOT KNOWN from
slot-element
256 to slot-element 4096.
02/20/2003 09:09:38 ANR9999D mmsscsi.c(9702): ThreadId<16> Volume may
still be
in the drive MT0.2.0.3 (\\.\Tape0).
02/20/2003 09:09:38 ANR8446I Manual intervention required for library
LB0.1.0.3.
02/20/2003 09:09:38 ANR8792E Unrecoverable drive failures on drive
MT0.2.0.3
(\\.\Tape0); drive is now taken offline.
02/20/2003 09:09:38 ANR8460E AUDIT LIBRARY process for library LB0.1.0.3
failed.
02/20/2003 09:09:38 ANR0985I Process 4 for AUDIT LIBRARY running in the
BACKGROUND completed with completion state FAILURE at
09:09:38.
It always says that it can't read the label of the tape inside the drive,
but I
always have checked in the tape before (it appear on the query libvol)
Platform: W2K, TSM 5.1.6.1, an external SDG 2108 R03 I have the lastest
firmware versions for the Library and the drives. There is an issue that
have
something to do with cabling a SANDGM but I don't have a SANDGM installed on
the library. Also I'm using the TSM Device Driver for the Library and the
windows drivers for the tapes.
Another issue, that doesn't have anything with TSM, someone know how to
upgrade an LTO RMU firmware via scsi or serial? In the proccess of
upgrading
it it failed, so now I don't have RMU control know, and on the manuals it
doesn't talk about it (as long as I can see, you can only upgrade drives or
library firmware through this process)
Thanks in advance.
Humberto Gómez
CAI
Universidad Católica Andrés Bello
-------------------------------------------------
This mail sent through IMP: http://horde.org/imp/
|
