Are you getting this pkthread error on NT servers?

Ben Bullock
Unix system manager
Micron Technology Inc.


> -----Original Message-----
> From: LeBlanc, Patricia [mailto:Patricia.Leblanc AT LIBERTYMUTUAL DOT COM]
> Sent: Wednesday, April 18, 2001 1:04 PM
> To: ADSM-L AT VM.MARIST DOT EDU
> Subject: Re: Dr. Watson in NT after installing TSM4.1
>
>
> Has anyone seen a pkthread error?
> We've upgraded from 3.1 to TSM 4.1.1.0 and keep getting this
> error that
> hangs the server.  It's not running and it's not down
> completely.  If it
> were down, our monitoring would pick that up.
>
> 7 servers have been upgraded, but only a couple are having
> this problem on a
> regular basis.
> Any thoughts would be greatly appreciated.
>
> > -----Original Message-----
> > From: Miller, Ryan [SMTP:Miller.Ryan AT PRINCIPAL DOT COM]
> > Sent: Thursday, April 12, 2001 3:33 PM
> > To:   ADSM-L AT VM.MARIST DOT EDU
> > Subject:      Re: Dr. Watson in NT after installing TSM4.1
> >
> > The one I can remember off the top of my head is the
> Fstypes option, it is
> > no longer supported and if it is in the OPT file, it will
> cause Dr Watson.
> > I believe we had another non supported option cause the
> same problem, but
> > I can't remember it.  Sorry.  I would review any OPT file
> you are going to
> > copy and question any options that seam out of place.
> That's how we found
> > ours.
> >
> > -----Original Message-----
> > From: LeBlanc, Patricia [mailto:Patricia.Leblanc AT LIBERTYMUTUAL DOT COM]
> > Sent: Thursday, April 12, 2001 2:21 PM
> > To: ADSM-L AT VM.MARIST DOT EDU
> > Subject: Re: Dr. Watson in NT after installing TSM4.1
> >
> >
> > What are the options you are talking about that are no
> longer supported??
> >
> > > -----Original Message-----
> > > From: Miller, Ryan [SMTP:Miller.Ryan AT PRINCIPAL DOT COM]
> > > Sent: Thursday, April 12, 2001 3:13 PM
> > > To:   ADSM-L AT VM.MARIST DOT EDU
> > > Subject:      Re: Dr. Watson in NT after installing TSM4.1
> > >
> > > Did you use the original OPT file?  If so, there are some
> options that
> > can
> > > cause Dr Watson errors.  They are options that are no
> longer supported
> > by
> > > the newer client, we have experienced this issue also and
> found this
> > > cause.
> > >
> > > -----Original Message-----
> > > From: Gottfried Scheckenbach
> > > [mailto:gottfried.scheckenbach AT xtelligent DOT de]
> > > Sent: Thursday, April 12, 2001 11:24 AM
> > > To: ADSM-L AT VM.MARIST DOT EDU
> > > Subject: Re: Dr. Watson in NT after installing TSM4.1
> > >
> > >
> > > Because there where no answers:
> > >
> > > Today I had the same problem - after upgrading a old ADSM
> 3.1 to TSM 4.1
> > > installation on NT with SP 3. Just after installation of
> SP 6 all went
> > > fine.
> > >
> > > Regards,
> > > Gottfried
> > >
> > >
> > > Shekhar Dhotre wrote:
> > > >
> > > > Hi all ,
> > > >
> > > > I   installed TSM server 4.1  on WINNT 4.0 service pack
> 4 , RAM 256 MB
> > > > whenever i  open configuration wizard   to configure any of the
> > > parameters in
> > > > TSM
> > > > DR. WATSON  shows his face ..  what should i check to
> correct this
> > > problem ..
> > > >
> > > > Thanks
> > > > shekhar
>