nv-l

Re: [NV-L] Global Load Balancing

2006-09-08 16:41:52
Subject: Re: [NV-L] Global Load Balancing
From: Leslie Clark <lclark AT us.ibm DOT com>
To: Tivoli NetView Discussions <nv-l AT lists.ca.ibm DOT com>
Date: Fri, 8 Sep 2006 16:37:41 -0400

Dave, this is the first I have heard of GLBP and I went and read about it at http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/ft_glbp.htm#wp1027177
It is described as a combination of HSRP and VRRP. It appears that there are no new mibs for this, just as there wasn't for HSRP until recently.

It sounds like you should be able to put the virtual address in the seedfile with % and Netview should handle it ok.  It will do an snmpget of the sysname at that address every 4 minutes, and only move it if it is not on the same device any more. Well, it will really be on all of them, but the one that responds is the one it is drawn on. Other than that, Netview cannot tell you much about the actual routing that is going on.

I would define the virtuals as HSRP, and discover the individual routers by their loopbacks. Have you had trouble properly discovering the groups?
Has anyone else had any experience with this protocol?

Cordially,

Leslie A. Clark
IT Services Specialist, Network Mgmt
Information Technology Services Americas
IBM Global Services
(248) 552-4968 Voicemail, Fax, Pager



reamd AT nationwide DOT com
Sent by: nv-l-bounces AT lists.ca.ibm DOT com

09/08/2006 03:31 PM
Please respond to
Tivoli NetView Discussions <nv-l AT lists.ca.ibm DOT com>

To
Tivoli NetView Discussions <nv-l AT lists.ca.ibm DOT com>
cc
nv-l AT lists.ca.ibm DOT com, nv-l-bounces AT lists.ca.ibm DOT com
Subject
Re: [NV-L] Global Load Balancing






Sorry,,,   Gateway Load Balancing Protocol....


reamd AT nationwide DOT com
 
Sent by:
nv-l-bounces AT lists.ca.ibm DOT com




09/08/2006 03:07 PM

Please respond to Tivoli NetView Discussions <nv-l AT lists.ca.ibm DOT com>
From
reamd AT nationwide DOT com
To
nv-l AT lists.ca.ibm DOT com
cc
Subject
[NV-L] Global Load Balancing








Hi All,

        I know you can configure the seedfile to correctly identify a HSRP configuration with a leading %..    Is there a way to configure GLBP (Global Load Balancing Protocol)?


Thanks, Dave



AIX 5300-03

Netview 7.1.4 FixPack4
_______________________________________________
NV-L mailing list
NV-L AT lists.ca.ibm DOT com
Unsubscribe:NV-L-leave AT lists.ca.ibm DOT com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to internal IBM'ers only)

_______________________________________________
NV-L mailing list
NV-L AT lists.ca.ibm DOT com
Unsubscribe:NV-L-leave AT lists.ca.ibm DOT com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to internal IBM'ers only)

_______________________________________________
NV-L mailing list
NV-L AT lists.ca.ibm DOT com
Unsubscribe:NV-L-leave AT lists.ca.ibm DOT com
http://lists.ca.ibm.com/mailman/listinfo/nv-l (Browser access limited to 
internal IBM'ers only)
<Prev in Thread] Current Thread [Next in Thread>