Re: [nv-l] Commands?
2005-12-12 16:30:14
Thank you to everyone who responded
- this helped a lot.
Kelly Root
Hewitt Associates
kjroot AT hewitt DOT com
don.turrentine AT amsouth DOT com
Sent by: owner-nv-l AT lists.us.ibm DOT com
12/12/2005 01:42 PM
Please respond to
nv-l AT lists.us.ibm DOT com |
|
To
| nv-l AT lists.us.ibm DOT com
|
cc
|
|
Subject
| Re: [nv-l] Commands? |
|
Kelly,
I use the nvUtil command much line John suggested to get the number of
routers, switches/hubs, and servers. I use the following cmds in
a shell
script:
# Total Counts
#
nvNodes=`/usr/OV/bin/nvUtil e "('isNode'=True)" | wc -l`
echo "Total number of nodes managed by NetView is: " $nvNodes
> $tmpfile
nvRtrs=`/usr/OV/bin/nvUtil e "('isRouter'=True)" | wc -l`
echo "Total number of routers managed by NetView is: " $nvRtrs
>> $tmpfile
nvSwitches=`/usr/OV/bin/nvUtil e "('isHub'=True)" | wc -l`
echo "Total number of switches/hubs managed by NetView is: "
$nvSwitches >>
$tmp
file
nvServers=`/usr/OV/bin/nvUtil e "('isServer'=True)" | wc -l`
echo "Total number of servers managed by NetView is: " $nvServers
>>
$tmpfile
Inorder for the Server count to work you must first setup an "isServer"
field in the database and then use nvdbimport to set this field to True
for
each server. I set this field for each server that is monitored by
NetView. Something that helps me is that I only add devices to NetView
using a seedfile, I never use auto discovery so this is easy to maintain.
As far as locations go you could use Smartsets that mimick your locations.
Our device naming scheme allows me to run run similar cmds to those above
using nvUtil and the 'IP Hostname' attribute to get node counts per
location. Another thing to look at would be the sysLocation field
of the
system MIB, assuming SNMP is enabled and these fields are set correctly.
Another way to get the number of routers (Gateways) is to use the following
command.
/usr/OV/bin/ovtopodump -l |grep ^NUMBER |sed 's/NUMBER OF//'|sed 's/:/:/'
The output is below.
NETWORKS: 5563
SEGMENTS: 5579
NODES: 2739
INTERFACES: 9873
GATEWAYS: 1312
-Don
---
"Kelly Root"
<kelly.root@hewit
t.com>
To
Sent by:
nv-l AT lists.us.ibm DOT com
owner-nv-l@lists.
cc
us.ibm.com
Subject
[nv-l] Commands?
12/12/2005 11:10
AM
Please respond to
nv-l AT lists.us DOT ibm
.com
I need to find out how many routers and servers Netview manages. What
is
the command?
I also need a report on what Netview is managing in a specific location.
What is the command to get this information?
Kelly Root
Hewitt Associates
kjroot AT hewitt DOT com
The information contained in this e-mail and any accompanying documents
may
contain information that is confidential or otherwise protected from
disclosure. If you are not the intended recipient of this message, or if
this message has been addressed to you in error, please immediately alert
the sender by reply e-mail and then delete this message, including any
attachments. Any dissemination, distribution or other use of the contents
of this message by anyone other than the intended recipient is strictly
prohibited.
The information contained in this e-mail and any accompanying documents may contain information that is confidential or otherwise protected from disclosure. If you are not the intended recipient of this message, or if this message has been addressed to you in error, please immediately alert the sender by reply e-mail and then delete this message, including any attachments. Any dissemination, distribution or other use of the contents of this message by anyone other than the intended recipient is strictly prohibited.
|
|
|