Re: [nv-l] Installing on RedHat Enterprise AS 4
2005-03-17 07:52:28
Mauro,
NetView 7.1.4 FP2 is not supported on
Red Hat Enterprise 4, NetView currently only supports Red Hat Enterprise
3.0 with update 4.
The original base NetView 7.1.4 CD will
not install correctly on Red Hat Enterprise 3.0, you must get the new CD
that shipped at the same time as Fix Pack 2. I have not actually
seen the CD label, but it should say something about being for NetView
on Red Hat 3.0 and SLES 9.
You need to remove the newer version
of pdksh wth "rpm -e pdksh-5.2.14-30",
then install NetView's older required version with "rpm -ivf
pdksh-5.2.14-8"
Mark F Sklenarik IBM SWG Tivoli
Solutions Quality Assurance Business Impact Management
and Event Correlation Software Quality Engineer
"Mauro" <conosciani.m AT adrtel DOT it>
Sent by: owner-nv-l AT lists.us.ibm DOT com
03/17/2005 06:44 AM
|
To
| <nv-l AT lists.tivoli DOT com>
|
cc
|
|
Subject
| [nv-l] Installing on RedHat
Enterprise AS 4 |
|
Dear all,
I’m trying to install Netview 7.1.4 on Red
Hat Enterprise AS 4 (!!!!!)………..I suppose that I have to install the
fixpack 2 as well, however I’m still stucking on the 7.1.4 base software
installation……
I’ve tried , first. To install the pdksh
packet and:
package pdksh-5.2.14-30 (which is newer than
pdksh-5.2.14-8) is already installed
file /bin/ksh from install of pdksh-5.2.14-8
conflicts with file from package pdksh-5.2.14-30
file /usr/share/man/man1/ksh.1.gz from install
of pdksh-5.2.14-8 conflicts with file from package pdksh-5.2.14-30
then I run
export LANG=en_US
export LC_MESSAGES=en_US
export LD_ASSUME_KERNEL=2.4.19
instalnv -k SERVER
Unless you cancel, the following operations
will be executed:
need to copy the machine independent
Message Catalogs to:
AdRTelNetMonitor:/usr/local/Tivoli/msg_cat
need to copy the machine independent
Portable Files to:
AdRTelNetMonitor:/usr/local/Tivoli/bin
need to copy the machine independent
Portable Files Configuration to:
AdRTelNetMonitor:/usr/local/Tivoli/bin
need to copy the architecture
specific NetView Prerequisites to:
AdRTelNetMonitor:/usr/local/Tivoli/bin/linux-ix86
need to copy the architecture
specific Binaries to:
AdRTelNetMonitor:/usr/local/Tivoli/bin/linux-ix86
need to copy the architecture
specific NetView Base Configuration to:
AdRTelNetMonitor:/usr/local/Tivoli/bin/linux-ix86
need to copy the architecture
specific NetView Features to:
AdRTelNetMonitor:/usr/local/Tivoli/bin/linux-ix86
need to copy the architecture
specific NetView Features Configuration to:
AdRTelNetMonitor:/usr/local/Tivoli/bin/linux-ix86
Continue(y/n)?y
Executing queued operation(s)
Distributing machine independent Message
Catalogs for AdRTelNetMonitor
... completed.
Distributing architecture specific
NetView Prerequisites for AdRTelNetMonitor
... completed.
Distributing architecture specific
Binaries for AdRTelNetMonitor
...... completed.
Distributing architecture specific
NetView Base Configuration for AdRTelNetMonitor
... completed.
Distributing architecture specific
NetView Features for AdRTelNetMonitor
..... completed.
Distributing architecture specific
NetView Features Configuration for AdRTelNetMonitor
.......................
Failure: the last few lines of the
error log (/tmp/NVS_714_NVFCONF_after.error):
Base operation complete...
+ echo NetView Installation encountered
errors and has not successfully completed.
NetView Installation encountered errors
and has not successfully completed.
+ echo Please check the log file /tmp/update.log
for more details about the errors.
Please check the log file /tmp/update.log
for more details about the errors.
+ echo Then run the uninstnv script
on the NetView cdrom to uninstall NetView,
Then run the uninstnv script on the
NetView cdrom to uninstall NetView,
+ echo fix the errors and reinstall
again.
fix the errors and reinstall again.
+ exit 1
after script failure
completed (with errors).
Install finished.
more /tmp/NVS_714_NVFCONF_after.error
Running customize script for fileset OVWIN.
ERROR: Customize script for
fileset OVWIN exited with code 2.
ERR_cfgbf_001
+ dspmsg -s 5 nv6000.cat 9999 nvconfigbf:
Failing doing configuration with ex
it code %s\n 2
+ >> /tmp/update.log
+ set +x
+ err_chk 2 bcfg_210 RUN_SCRIPT /usr/OV/install/tools/nvconfigbf
ERR_bcfg_210
+ dspmsg -s 5 nv6000.cat 9999 base:
Failing base.config with exit code %s\n 2
+ >> /tmp/update.log
+ set +x
base: Saving log files to /tmp/NVfail.tar
awk: cmd. line:1: warning: escape sequence
`\/' treated as plain `/'
+ funct_return=1
+ '[' 1 = 0 ']'
+ '[' '' = '' ']'
Any Idea o suggestion
|
|
|