Re: [nv-l] netview name lookup
2003-12-22 15:51:21
With regards to Leslie's note. If I am using the Name of the Gateway and not the IP address of it would it not go in and resolve to the correct IP and therefore Selection name. And if it does not and the gateway name is invalid what exactly will happen then?
|
| Leslie Clark <lclark AT us.ibm DOT com>
Sent by: owner-nv-l AT lists.us.ibm DOT com
12/22/2003 10:09 AM
Please respond to nv-l
|
To: nv-l AT lists.us.ibm DOT com
cc:
Subject: Re: [nv-l] netview name lookup |
A common area of confusion with the location.conf file gateway entries: you cannot put just any old address in there. The match will be done on the Selection Name that the router ends up with.
Cordially,
Leslie A. Clark
IBM Global Services - Systems Mgmt & Networking
Detroit
| "Christopher J Petrina" <cjp8 AT meadwestvaco DOT com>
Sent by: owner-nv-l AT lists.us.ibm DOT com
12/22/2003 09:29 AM
Please respond to nv-l
|
To: nv-l AT lists.us.ibm DOT com
cc:
Subject: Re: [nv-l] netview name lookup |
This is how I would figure it did the Name resolution. HOwever with Netview running on an AIX box, my UNIX guru's have come to tell me that name resolution is only done via a DNS server from AIX. AIX cannot be configured to use the /etc/hosts file for resolution. We ahve a DNS server that it attaches to. And your answer is what I was looking for
Thank you
Chris Petrina
|
| Jane Curry <jane.curry AT skills-1st.co DOT uk>
Sent by: owner-nv-l AT lists.us.ibm DOT com
12/20/2003 06:57 AM
Please respond to nv-l
|
To: nv-l AT lists.us.ibm DOT com
cc:
Subject: Re: [nv-l] netview name lookup |
NetView himself has no name-to-address resolution mechanism - he uses
whatever the host Operating System uses. That is, if all you have is a
hosts file with the NetView box in it, everything else will have IP
addresses as labels. It is strongly recommended that you have a
reliable DNS employed by the NetView system (preferably with the NetView
system acting as a caching / secondary DNS server).
Cheers,
Jane
Christopher J Petrina wrote:
>
> how does netview look attempt to determine the name of a device.
> i.e. in my location.conf file I am using names in place of IP
> addresses for my gateways. How does Netview resolve the name on a AIX
> box?
--
Tivoli Certified Consultant & Instructor
Skills 1st Limited, 2 Cedar Chase, Taplow, Bucks, SL6 0EU, UK
Tel: +44 (0)1628 782565
Copyright (c) 2003 Jane Curry <jane.curry AT skills-1st.co DOT uk>. All rights reserved.
________________________________________________________________________
This email has been scanned for all viruses by the MessageLabs SkyScan
service._______________________________________________________________
|
<Prev in Thread] |
Current Thread |
[Next in Thread>
|
- [nv-l] netview name lookup, Christopher J Petrina
- Re: [nv-l] netview name lookup, Christopher J Petrina
- Re: [nv-l] netview name lookup, James Shanks
- Re: [nv-l] netview name lookup, Leslie Clark
- Re: [nv-l] netview name lookup, Leslie Clark
- Re: [nv-l] netview name lookup,
Christopher J Petrina <=
- Re: [nv-l] netview name lookup, Christopher J Petrina
- RE: [nv-l] netview name lookup, Barr, Scott
- Re: [nv-l] netview name lookup, Jon Austin
- RE: [nv-l] netview name lookup, Christopher J Petrina
- Re: [nv-l] netview name lookup, Leslie Clark
- Re: [nv-l] netview name lookup, Christopher J Petrina
- Re: [nv-l] netview name lookup, Leslie Clark
|
|
|