Fawad,
I am running nvmaputil.sh directly from the command line. My environment
settings should be correct....Nvenvironment was set via .profile at login.
I've seen the delays in the past as well, but no more than a minute. The
server that Netview is on is a screamer. CPU Load average for ovtopmd is
usually around 0.01 and ovwdb is 0.7
I'll keep digging. If I have to open up a call with support, I will post the
results.
Thanks
Channing Hill
EMS Analyst II
BB&T
(252) 246-3642
-----Original Message-----
From: Qureshi, Fawad [mailto:Fawad.Qureshi AT ssa DOT gov]
Sent: Monday, November 03, 2003 1:29 PM
To: 'nv-l AT lists.us.ibm DOT com'
Subject: RE: [nv-l] nvmaputil.sh command not working?
Couple of comments:
1. Yes, you need to either have R/W map open or netviewd running in R/W mode
for nvmaputil.sh to work. Though I have seen problems with netviewd, but
always works if R/W default is open.
2. If you are calling nvmaputil.sh from a script, does it work directly from
the command line?
3. I have seen delays of up to several minutes, depending on how busy your
Netview server is, before the map and databases are updated.
Cheers
Fawad Qureshi
Division of Network Engineering - SSA / RSIS
410-965-4413
-----Original Message-----
From: owner-nv-l-digest AT lists.us.ibm DOT com
[mailto:owner-nv-l-digest AT lists.us.ibm DOT com] On Behalf Of Hill, Channing
Sent: Monday, November 03, 2003 1:10 PM
To: 'nv-l AT lists.us.ibm DOT com'
Subject: RE: [nv-l] nvmaputil.sh command not working?
I'm sure all you need is a R/W map opened OR netviewd running in R/W mode. I
successfully performed nvmaputil.sh commands in a test environment without
the netviewd running....just the native R/W map. I'll probably open up a
case with support unless anybody has anything to add. I assume its either
something with my environment or Java.
Channing Hill
EMS Analyst II
BB&T
(252) 246-3642
-----Original Message-----
From: Paul Stroud [mailto:pstroud AT bellsouth DOT net]
Sent: Monday, November 03, 2003 12:14 PM
To: nv-l AT lists.us.ibm DOT com; Hill, Channing; 'nv-l AT lists.us.ibm DOT com'
Subject: Re: [nv-l] nvmaputil.sh command not working?
If I am not mistaken, the interface that allows for this is the web client.
You must have netviewd up and running in read-write mode for it to work. I
may be incorrect and if I am, someone please let me know. If this is
the case, and doing it without netviewd running, does not produce an error,
you should open a case with support.
Paul
On Monday 03 November 2003 11:57, Hill, Channing wrote:
> Netview 7.1.3 w/ Fixpack 1 on AIX 5.1
>
> I've recently overhauled our production Netview system...OS installed
> from scratch and Netview 7.1.3 installed via migration method (
> databases, conf files, etc. were pulled from a properly working "test"
> system. Everything appears to be working as designed....just like I
> had tested except that I can't get "nvmaputil.sh" to do anything. It
> runs and completes with no errors but has no effect on the symbols or
> objects it is ran on.
>
> Everything is in place for it to work.....I have one native R/W map
> (default) opened, the "NVenvironment" script was ran from .profile at
> login, and I am using the right symbol ID's (taken from ovmapdump) and
> or selection names in the command.
>
> Anybody got any ideas as to what's missing or why its not working??
>
> Channing Hill
> EMS Analyst II
> BB&T
> (252) 246-3642
|
