This is a multipart message in MIME format. On UNIX you use the Smartset/Collection editor. It has both GUI and text
editor modes. You can use the GUI mode. Just click the buttons.
Type in "collectioned" or pull down Tools --> Smartset Editor
To get a smartset with non-SNMP objects, create one with the attribute
'isSNMPSupported' equal to false.
To get a smartset with only MS objcets, create one with the vendor equal
to Microsoft or the attribute SNMP sysObjectId like (~) 1.3.6.1.4.1.311.
(make certain to omit the initial dot "." in string here). Works ofr me.
You can of course continue this logic to add other vendors or make
compound conditions for your smartsets.
James Shanks
Level 3 Support for Tivoli NetView for UNIX and NT
Tivoli Software / IBM Software Group
bducharme AT avdl DOT com
Sent by: owner-nv-l AT tkg DOT com
11/12/2001 03:19 PM
Please respond to IBM NetView Discussion
To: IBM NetView Discussion <nv-l AT tkg DOT com>
cc:
Subject: Réf. : Re: [NV-L] Remove Workstation from Map
How to define Smartsets
that include workstation and non-snmp equipment ?
Benoit
"Leslie Clark" <lclark AT US.IBM DOT COM>@tkg.com le 2001-11-12 10:57:04
Veuillez répondre à IBM NetView Discussion <nv-l AT tkg DOT com>
Envoyé par : owner-nv-l AT tkg DOT com
Pour : IBM NetView Discussion <nv-l AT tkg DOT com>
cc :
Objet : Re: [NV-L] Remove Workstation from Map
This is done with the seedfile. There are a couple of ways.
First, if you have a good addressing scheme, you should exclude them
by address range. This is the best performer. If you have assigned DHCP
address ranges, put them in your seedfile like this:
!10.*.23-150.40-255
If you don't have a tidy addressing scheme, or if you also have a lot
of workstations that don't abide by the rules, you can exclude them by
snmp sysObject id. Since most of them will be either non-snmp, or
Microsoft, you can exclude them like this;
!@oid 0 # excludes non-snmp
!@oid 1.3.6.1.4.1.311.* # excludes MS
The second one would also exclude servers, so you would then add
in an explicit list of the servers that you do want to allow.
Make sure netmon is using the seedfile, and has re-read it.
To get them out of the map after updating the seedfile you can
either rediscover the entire network, or you can locate and
delete them. To locate and delete them, define Smartsets
that include them. Then you can grab them easily and delete
them. If there are a lot, this can take quite a while, but if you have
done a lot of map customization it will be worth the wait. I prefer
to stop netmon during the delete, and after all of the events for
the deletions have come in, do an ovtopofix -a.
Cordially,
Leslie A. Clark
IBM Global Services - Systems Mgmt & Networking
Detroit
bducharme@avdl
.com To: nv-l AT tkg DOT com
Sent by: cc:
owner-nv-l@tkg Subject: [NV-L] Remove
Workstation from Map
.com
11/12/01 10:10
AM
Please respond
to IBM NetView
Discussion
How can we remove and prevent Workstation from getting in the Netview map
?
Thanks
Benoit
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
On UNIX you use the Smartset/Collection editor. It has both GUI and text editor modes. You can use the GUI mode. Just click the buttons.
Type in "collectioned" or pull down Tools --> Smartset Editor
To get a smartset with non-SNMP objects, create one with the attribute 'isSNMPSupported' equal to false.
To get a smartset with only MS objcets, create one with the vendor equal to Microsoft or the attribute SNMP sysObjectId like (~) 1.3.6.1.4.1.311. (make certain to omit the initial dot "." in string here). Works ofr me.
You can of course continue this logic to add other vendors or make compound conditions for your smartsets.
James Shanks
Level 3 Support for Tivoli NetView for UNIX and NT
Tivoli Software / IBM Software Group
| bducharme AT avdl DOT com
Sent by: owner-nv-l AT tkg DOT com
11/12/2001 03:19 PM
Please respond to IBM NetView Discussion
|
To: IBM NetView Discussion <nv-l AT tkg DOT com>
cc:
Subject: Réf. : Re: [NV-L] Remove Workstation from Map
|
How to define Smartsets
that include workstation and non-snmp equipment ?
Benoit
"Leslie Clark" <lclark AT US.IBM DOT COM>@tkg.com le 2001-11-12 10:57:04
Veuillez répondre à IBM NetView Discussion <nv-l AT tkg DOT com>
Envoyé par : owner-nv-l AT tkg DOT com
Pour : IBM NetView Discussion <nv-l AT tkg DOT com>
cc :
Objet : Re: [NV-L] Remove Workstation from Map
This is done with the seedfile. There are a couple of ways.
First, if you have a good addressing scheme, you should exclude them
by address range. This is the best performer. If you have assigned DHCP
address ranges, put them in your seedfile like this:
!10.*.23-150.40-255
If you don't have a tidy addressing scheme, or if you also have a lot
of workstations that don't abide by the rules, you can exclude them by
snmp sysObject id. Since most of them will be either non-snmp, or
Microsoft, you can exclude them like this;
!@oid 0 # excludes non-snmp
!@oid 1.3.6.1.4.1.311.* # excludes MS
The second one would also exclude servers, so you would then add
in an explicit list of the servers that you do want to allow.
Make sure netmon is using the seedfile, and has re-read it.
To get them out of the map after updating the seedfile you can
either rediscover the entire network, or you can locate and
delete them. To locate and delete them, define Smartsets
that include them. Then you can grab them easily and delete
them. If there are a lot, this can take quite a while, but if you have
done a lot of map customization it will be worth the wait. I prefer
to stop netmon during the delete, and after all of the events for
the deletions have come in, do an ovtopofix -a.
Cordially,
Leslie A. Clark
IBM Global Services - Systems Mgmt & Networking
Detroit
bducharme@avdl
.com To: nv-l AT tkg DOT com
Sent by: cc:
owner-nv-l@tkg Subject: [NV-L] Remove
Workstation from Map
.com
11/12/01 10:10
AM
Please respond
to IBM NetView
Discussion
How can we remove and prevent Workstation from getting in the Netview map ?
Thanks
Benoit
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
|