Re: snmp setup
2001-10-05 15:35:39
This is a multipart message in MIME format. First, loading the MIB does not add trap settings, period. Never has in
Netview . You can only add trap settings from a MIB by running mib2trap
on the MIB. This creates, in NT, a .bat file, (a script in UNIX), which
contains a series of addtrap commands built from the TRAP-TYPE or
NOTIFICATION-TYPE statements in the MIB. If the .bat file is empty, then
there were no such statements in the MIB, which means that it does not
define any traps. If you are in doubt about that, then browse the MIB
with Notepad or Wordpad an take a look. If the .bat file is not empty,
then you must execute that file to add the traps. Adding the Enterprise
Id manually is not necessary. Addtrap will do that and add the specific
traps as well.
James Shanks
Level 3 Support
Tivoli NetView for UNIX and NT
Tivoli Software
IBM Software Group
Please note that my new id is jshanks AT us.ibm DOT com
Daniel Lehman <dlehman AT hurricanetechgroup DOT com>
Sent by: owner-nv-l AT tkg DOT com
10/05/2001 02:10 PM
Please respond to IBM NetView Discussion
To: nv-l AT tkg DOT com
cc:
Subject: [NV-L] snmp setup
Hello All,
I am having a little issue, i loaded the required mib in to Netview 6.02
on NT. I am able to use the MIB Browser and walk through the tree
succesfully. When i go into the view the trap settings there is nothing
visible under the Enterprise for this MIB, so i created a new entry for
the Enterprise. Still no traps are visible. I attempted to use mib2trap
with no success, any and all advice for be greatly appreciated.
Thanks..........
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
First, loading the MIB does not add trap settings, period. Never has in Netview . You can only add trap settings from a MIB by running mib2trap on the MIB. This creates, in NT, a .bat file, (a script in UNIX), which contains a series of addtrap commands built from the TRAP-TYPE or NOTIFICATION-TYPE statements in the MIB. If the .bat file is empty, then there were no such statements in the MIB, which means that it does not define any traps. If you are in doubt about that, then browse the MIB with Notepad or Wordpad an take a look. If the .bat file is not empty, then you must execute that file to add the traps. Adding the Enterprise Id manually is not necessary. Addtrap will do that and add the specific traps as well.
James Shanks
Level 3 Support
Tivoli NetView for UNIX and NT
Tivoli Software
IBM Software Group
Please note that my new id is jshanks AT us.ibm DOT com
| Daniel Lehman <dlehman AT hurricanetechgroup DOT com>
Sent by: owner-nv-l AT tkg DOT com
10/05/2001 02:10 PM
Please respond to IBM NetView Discussion
|
To: nv-l AT tkg DOT com
cc:
Subject: [NV-L] snmp setup
|
Hello All,
I am having a little issue, i loaded the required mib in to Netview 6.02 on NT. I am able to use the MIB Browser and walk through the tree succesfully. When i go into the view the trap settings there is nothing visible under the Enterprise for this MIB, so i created a new entry for the Enterprise. Still no traps are visible. I attempted to use mib2trap with no success, any and all advice for be greatly appreciated. Thanks..........
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
|
|
|