I don't know who told you to re-cycle nvcorrd, but that is not really
necessary, provided all you are trying to do is change a ruleset in
ESE.automation, and you have no other rulesets running which have action
nodes in them, which might fail as a result.
actionsvr loads the rulesets in ESE.automation and when he goes away,
nvcorrd stops running them and unloads them automatically. So you can do
the less-disruptive change of just ovstop / ovstart actionsvr. That way
your user event windows can stay open. Of course, if those are running
other rulesets which have actions in them, you may lose those actions while
the actionsvr re-cycle takes place. Some folks do have actions running out
of event windows or even in their TEC rulesets being run by nvserverd.
I suspect that what you were told was with the best of intentions how not
to have any unexpected side-effects (such as rulesets in user windows or
for TEC forwarding with actions in them that might fail) by restarting the
whole mechanism. But that is not always necessary if you are careful
about what you are doing.
James Shanks
Level 3 Support
Tivoli NetView for UNIX and NT
"Scott Barr" <scott_barr AT csgsystems DOT com>@tkg.com on 08/13/2001 10:17:18
AM
Please respond to IBM NetView Discussion <nv-l AT tkg DOT com>
Sent by: owner-nv-l AT tkg DOT com
To: "IBM NetView Discussion" <nv-l AT tkg DOT com>
cc:
Subject: RE: [NV-L] Ruleset Automatic action ??
After recent conversations with support, I was told cycle NVCORRD not just
actionsvr.
-----Original Message-----
From: owner-nv-l AT tkg DOT com [mailto:owner-nv-l AT tkg DOT com]On Behalf Of
BAUDOUX
BERNARD
Sent: Monday, August 13, 2001 8:47 AM
To: 'IBM NetView Discussion'
Subject: RE: [NV-L] Ruleset Automatic action ??
Jeff,
restart daemon 'actionsvr', and you can see if your new ruleset has been
successfully registered in /usr/OV/log/nvaction.alog
Regards,
Bernard Baudoux
Phone: +32 (0)2/565.24.68
e-mail : bernard.baudoux AT fortisbank DOT com
> -----Original Message-----
> From: Jeff Fitzwater [SMTP:jfitz AT Princeton DOT EDU]
> Sent: Monday, 13 August, 2001 15:42
> To: netview users
> Subject: [NV-L] Ruleset Automatic action ??
>
> Solaris 7
> Netview 6.02
>
>
> If I have a Ruleset defined in the "ESE.automation" file, and I make a
> change to that ruleset, what process
> should I restart to have the changes take effect?
>
>
> Thank you;
>
> Jeff Fitzwater
> CIT Systems & networking
> Princeton University
>
> _________________________________________________________________________
> NV-L List information and Archives: http://www.tkg.com/nv-l
This email and any attached files are confidential and may be legally
privileged.
If you are not the intended recipient, any disclosure, reproduction,
copying, distribution, or other dissemination or use of this communication
is strictly prohibited.
If you have received this transmission in error please notify the sender
immediately and then delete this email.
Email transmission cannot be guaranteed to be secure or error free as
information could be intercepted, corrupted, lost, destroyed, arrive late
or
incomplete, or contain viruses.
The sender therefore is in no way liable for any errors or omissions in the
content of this message, which may arise as a result of email transmission.
If verification is required, please request a hard copy.
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
_________________________________________________________________________
NV-L List information and Archives: http://www.tkg.com/nv-l
|
