OK, now, since I've got 2 IP addr. for my NetView server, can I recieve
traps on both of them ?
My objective is to have 2 routes for traps so that if one route fails
the traps still reach the management station through the second one ...

Thanks

---------------------
Alain Menezes   
ASLK-CGER Services GIE                          Tel.:  +32 2 228.55.74
Rue Fossé-aux-Loups, 48                               Fax.:  +32 2 228.83.69
1000  Bruxelles                                         Email:
a.menezes AT aslk-cger DOT be




> -----Original Message-----
> From: Owens, Blaine C [SMTP:bowens AT EASTMAN DOT COM]
> Sent: vendredi 16 avril 1999 16:19
> To:   NV-L AT UCSBVM.UCSB DOT EDU
> Subject:      Re: AW: 2 Network adapters
> 
> HI, this is the way it works. You only have one default gateway. If
> you do
> "netstat -r" you will see that there are routing table entries for
> each
> interface, i.e. - anything for subnet 1 will be via the interface on
> subnet
> 1 and anything for subnet 2 will be via the interface on subnet 2. The
> default gateway is for subnets 3,4,5, etc. Decide which router would
> be best
> for "everything else" and set this as your default gateway (note - the
> default gateway must have an interface on either subnet 1 or subnet
> 2).
>  
> Blaine Owens
> Eastman Chemical Company
> Email - bowens AT eastman DOT com
> Phone - (423)229-3579
> Fax     - (423)229-1188
> 
> > -----Original Message-----
> > From: Gil Irizarry [SMTP:IRIZARRG AT labs.wyeth DOT com]
> > Sent: Friday, April 16, 1999 10:08 AM
> > To:   NV-L AT UCSBVM.ucsb DOT edu
> > Subject:      Re: AW: 2 Network adapters
> > 
> > Alain:
> >   I do have deferent adapters pointing to different subnets. When I
> use
> > smitty to config the adapters default gateway, it changes the
> default
> > gateway for all adapters to the same gateway address. If anyone
> knows of a
> > way to avoid this, please let me know.
> > Gil Irizarry
> > 
> > >>> "MENEZES, ALAIN" <a.menezes AT ASLK-CGER DOT BE> 04/16 9:31 AM >>>
> > What if the adapters are in different subnets and use different
> default
> > gateways ?
> > ---------------------
> > Alain Menezes       
> > ASLK-CGER Services GIE                          Tel.:  +32 2
> 228.55.74
> > Rue Fossé-aux-Loups, 48                               Fax.:  +32 2
> > 228.83.69
> > 1000  Bruxelles                                         Email:
> > a.menezes AT aslk-cger DOT be 
> > 
> > 
> > 
> > 
> > > -----Original Message-----
> > > From: Gil Irizarry [SMTP:IRIZARRG AT LABS.WYETH DOT COM] 
> > > Sent: vendredi 16 avril 1999 15:23
> > > To:   NV-L AT UCSBVM.UCSB DOT EDU 
> > > Subject:      Re: AW: 2 Network adapters
> > > 
> > > Ralph:
> > >   When looking at your TCP/IP configuration for the two adapters,
> do
> > > they share the same default gateway?. I have FDDI & ETH, but, the
> > > configuration for each have the same default gateway. When I
> change
> > > one, the other get updated also with the same IP address for
> default
> > > gateway. I have my routers with two entries for the snmp-server
> > > utilizing the two different adapters on my AIX 4.3.2 NV5..1
> server.  I
> > > believe that all request from the box go out on the adapter with
> the
> > > same subnet as the default gateway.
> > > GIl Irizarry
> > > 
> > > >>> Schiffinger Ralph 2100 <Ralph.Schiffinger AT ERSTEBANK DOT AT> 04/16
> 5:42
> > > AM >>>
> > > None i could think of.
> > > Running my server with 2 adapters.
> > > Adapter 1 is TokenRing, doing my manage-the-manager-traffic.
> > > Adapter 2 is Fddi, doing my manage-the-network-traffic.
> > > Nullo problemo.
> > > Cordially, Ralph.
> > > iT-AUSTRIA / OE2100 / TK-NET
> > > Tel  (mobil)  0664 1908469
> > > Tel  (iT-A)    21717 58948
> > > FAX (iT-A)    21717 58979
> > > Mailto:Ralph.Schiffinger AT erstebank DOT at 
> > > 
> > > 
> > >  -----Ursprüngliche Nachricht-----
> > > Von:    MENEZES, ALAIN [SMTP:a.menezes AT ASLK-CGER DOT BE] 
> > > Gesendet am:    Freitag, 16. April 1999 12:24
> > > An:     NV-L AT UCSBVM.ucsb DOT edu; Schiffinger Ralph 2100
> > > Betreff:        2 Network adapters
> > > 
> > > 
> > > Hi all,
> > > 
> > > I'm thinking of configuring a second network adapter on my NetView
> > > server; it will be connected to another subnet, but will be able
> to
> > > see
> > > all the subnets the 1st one can ....
> > > Are there any know problems/issues regarding the way NetView will
> > > (populate,) manage the DB ?
> > > 
> > > Any info will be appreciated.
> > > 
> > > Thanks
> > >  ---------------------
> > > Alain Menezes     
> > > ASLK-CGER Services GIE                          Tel.:  +32 2
> 228.55.74
> > > Rue Fossé-aux-Loups, 48                               Fax.:  +32 2
> > > 228.83.69
> > > 1000  Bruxelles                                         Email:
> > > a.menezes AT aslk-cger DOT be