See Leslie's message, as well as CISCO-GENERAL-TRAPS.my the v1 directory.
This is a bit of a chicken-and-egg question, but do you know what kind of
traps your cisco devices are sending?  Sometimes knowing what they're
passing to you helps in navigating all the mibs contained in the
subdirectories.

> -----Original Message-----
> From: Todd E. Lewis [SMTP:telewis AT PROVIDENTBANKMD DOT COM]
> Sent: Tuesday, April 13, 1999 12:19 PM
> To:   NV-L AT UCSBVM.ucsb DOT edu
> Subject:      Re: Does anyone know what mib/trap files from cisco and bay
> workwith Netview for NT 5.1?
>
> Do you know if they also contain trap definitions?
>
> >>> OGrant <OGrant AT PEC DOT COM> 04/13 11:44 AM >>>
> I'm using Netview/Nt as well, *and* sent you the wrong address - it's
> ftp://ftp.cisco.com/pub/mibs/ .  You'll definitely want to check out the
> /supportlists subdirectory.  Also, have a look at cisco's document
> entitled
> "Introduction to Cisco MIBs" - the url for it got chopped off on my copy,
> but it starts
> http://www.cisco.com/univercd/cd/td/doc/product/lan/cat5000/c5k3../mover.h
> t
> blah blah.  Best to do a search from cisco's home page.
>
> What are trying exactly to do with your cisco devices?  I only ask because
> I
> originally sought out to get rid of those annoying "DEFAULT FMT" trap
> messages netview's event browser kept displaying for my 3600 series
> routers.
> After loading *all* of the mibs for that router as specified in the
> support
> list, I eventually cheated and just added the oid for the router to my
> trapd.conf file (I know, I should have also monkeyed with oidtotype), and
> specified the "authentication failure", "link up", and "link down" traps.
> Proceded to eliminate some 80% of the "default fmt" messages.  This, of
> course, represents the quick-and-dirty approach.
>
> > -----Original Message-----
> > From: Todd E. Lewis [SMTP:telewis AT PROVIDENTBANKMD DOT COM]
> > Sent: Tuesday, April 13, 1999 11:24 AM
> > To:   NV-L AT UCSBVM.ucsb DOT edu
> > Subject:      Re: Does anyone know what mib/trap files from cisco and
> bay
> > workwith Netview for NT 5.1?
> >
> > We have cisco 7000,7513,2503 mostly. Cisco's site talks about mibs but
> > they appear to be used with HPOV or UNIX version Netview. Do you know of
> a
> > specific on that will work with the models I listed and NEtview for NT?
> >
> > >>> OGrant <OGrant AT PEC DOT COM> 04/13 11:06 AM >>>
> > Regarding cisco, have you checked out http://www.cisco.com/public/mibs/
> ?
> > Not knowing what type of equipment you have, it may be worth a look -
> > Oliver
> > Grant
> >
> > > -----Original Message-----
> > > From: Todd E. Lewis [SMTP:telewis AT PROVIDENTBANKMD DOT COM]
> > > Sent: Tuesday, April 13, 1999 10:35 AM
> > > To:   NV-L AT UCSBVM.ucsb DOT edu
> > > Subject:      Does anyone know what mib/trap files from cisco and bay
> > work
> > > with Netview for NT 5.1?
> > >
> > > Does anyone know what mib/trap files from cisco and bay work with
> > Netview
> > > for NT 5.1?