What's your policy look like: "bppllist <policyname> -U", and when did it
last run?
-M
-----Original Message-----
From: Brooks, Jason [mailto:brooksje AT longwood DOT edu]
Sent: Monday, March 06, 2006 2:21 PM
To: Brooks, Jason; Donaldson, Mark - Broomfield, CO;
veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] Job Prediction Accuracy?
Bpschedreq is there. Tried the following:
D:\Program Files\VERITAS\NetBackup\bin\admincmd>bpschedreq.exe -M calvin
-predict 03/06/2006
With different time stamps.
Here's what my schedule contains: a differential-incremental and full
backup of the Exchange mailboxes. The differential should kick off
tonight at 20:00 - that's the schedule. So, plugging in 20:00:00 after
the date still shows nothing. I actually can't get any response out of
bpschedreq.exe.
Ideas?
Thanks,
Jason
-----Original Message-----
From: veritas-bu-admin AT mailman.eng.auburn DOT edu
[mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu] On Behalf Of Brooks,
Jason
Sent: Monday, March 06, 2006 4:06 PM
To: Mark.Donaldson AT cexp DOT com; veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] Job Prediction Accuracy?
Version 6. I didn't recognize it either. I couldn't remember what to
run, so I opened up the pdf of Version 6 Commands, and searched for
predict. That's the only command I landed. I'll check the other as
well.
Thanks,
Jason
-----Original Message-----
From: Mark.Donaldson AT cexp DOT com [mailto:Mark.Donaldson AT cexp DOT com]
Sent: Monday, March 06, 2006 4:03 PM
To: Brooks, Jason; veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] Job Prediction Accuracy?
I don't recognize the command. What version are you running.
I'd look ahead with this:
bpschedreq:
-terminate -jobid <jobid>
-suspend -jobid <jobid>
[-M <master_server,...,master_server>]
-tables
-read_stunits
-read_stu_config
-predict datetime [-L]
-verbose level
format for datetime is mm/dd/yyyy HH:MM:SS
note, the datetime format. It only predicts for a specific
hour/min/sec, you might be defaulting to 00:00:00 by leaving this off.
-M
-----Original Message-----
From: veritas-bu-admin AT mailman.eng.auburn DOT edu
[mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu]On Behalf Of Brooks,
Jason
Sent: Monday, March 06, 2006 1:49 PM
To: veritas-bu AT mailman.eng.auburn DOT edu
Subject: [Veritas-bu] Job Prediction Accuracy?
I was trying to figure out why my recently implemented backups of an
Exchange server did not occur over the weekend. I made sure that the
Policies were active - yes. I checked the schedule to be valid - yes.
The Information Store policy had a job priority of 1; I've upped it to 4
(like some other jobs). The Mailbox policy had a job priority of 0;
I've changed it to a 4 as well. But when I run D:\Program
Files\VERITAS\NetBackup\bin\admincmd>nbpemreq.exe -predict -date
03/06/2006
the Exchange backups are not listed at all. So, is nbpemreq.exe a)
broken; b) fine, but something else is amiss; c) the wrong cmd-line tool
to use for this.
Thanks for any suggestions,
Jason
------------
Jason Brooks
Computer Systems Engineer
IITS - Longwood University
voice - (434) 395-2916
fax - (434) 395-2035
mailto:<brooksje AT longwood DOT edu>
_______________________________________________
Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
_______________________________________________
Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
|