[Veritas-bu] Setting up Mail Notifications
2005-11-18 04:14:05
Subject: |
[Veritas-bu] Setting up Mail Notifications |
From: |
Jim Peppas" <perf AT peppas DOT gr (Jim Peppas) |
Date: |
Fri, 18 Nov 2005 09:14:05 +0000 |
HI,
I use the blat command with specifing the server each time. I run it once with
the -install option and then I don't supply the server again.
Regards,
Jim Peppas
> -------Original Message-------
> From: j. okabayashi <fishnfool AT gmail DOT com>
> Subject: Re: [Veritas-bu] Setting up Mail Notifications
> Sent: 17 Nov '05 20:48
>
> Thanks Mark. I actually went through and manually straightened it out.
> The problem I'm having now is that I'm still not getting notifications
> after following the veritas article. Does anyone else know what needs to
> be done other than putting the the e-mail server in the following line?
>
>
> @blat %3 -s %2 -t %1 -i NetBackup -server [LINK:
> http://EMAILSERVER.MYCOMPANY.COM] EMAILSERVER.MYCOMPANY.COM -q
>
>
> I can send email using blat so I know that works. It has to be something
> in the nbmail file. Any help would be appreciated.
>
>
> Thanks.
>
> Jason
>
>
> On 11/17/05, [LINK: MAILTO:MARK.DONALDSON AT CEXP DOT COM]
> MARK.DONALDSON AT CEXP DOT COM <[LINK: mailto:Mark.Donaldson AT cexp DOT com]
> Mark.Donaldson AT cexp DOT com> wrote:
>
> this is probably because of your editor choice. I think Notepad uses a
> <CR><LF> for a flat file while Wordpad uses a <CR> only.
>
>
> For DOS to UNIX, I always use Wordpad. I'm not sure what to do for your
> situation other than suggest trying a different editor.
>
>
> -M
>
> -----Original Message-----
> FROM: [LINK: mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu]
> veritas-bu-admin AT mailman.eng.auburn DOT edu [mailto:[LINK:
> mailto:veritas-bu-admin AT mailman.eng.auburn DOT edu]
> veritas-bu-admin AT mailman.eng.auburn DOT edu]ON BEHALF OF j. okabayashi
> SENT: Wednesday, November 16, 2005 6:41 PM
> TO: [LINK: mailto:veritas-bu AT mailman.eng.auburn DOT edu]
> veritas-bu AT mailman.eng.auburn DOT edu
> SUBJECT: [Veritas-bu] Setting up Mail Notifications
>
>
> Can somebody help be configure BLAT on my Master server? It is NBU 5.1
> mp3a on W2k3. I followed the directions from the veritas article, but I'm
> not getting any e-mails. One thing I noticed, after I edited the
> NBmail.com file it lost it's "structure" . See below.
>
>
> @REM $Header: nbmail.cmd,v 1.3 2003/06/25 18:07:46 [LINK:
> mailto:$@REM@REM] $@REM@REM [LINK: mailto:bcpyrght@REM] bcpyrght@REM
> [LINK:
>
> mailto:***************************************************************************@REM]
>
> ***************************************************************************@REM
> * $VRTScprght: Copyright 1993 - 2004 VERITAS Software Corporation, All
> Rights Reserved $ [LINK: mailto:*@REM] *@REM [LINK:
>
> mailto:***************************************************************************@REM]
>
> ***************************************************************************@REM
> [LINK: mailto:ecpyrght@REM] ecpyrght@REM @REM - - - - - - - - - - - - - -
> - - - - - - - - - - - - - - - - - - - - - - - [LINK: mailto:-@REM] -@REM -
>
> [LINK: mailto:-@REM] -@REM - HOW TO SEND MAIL FROM THE NT NETBACKUP
> SERVER [LINK: mailto:-@REM] -@REM -
> [LINK:
> mailto:-@REM] -@REM - NetBackup checks if the mail script
> (NetBackup\Bin\nbmail.cmd) exists. [LINK: mailto:-@REM] -@REM - If the
> script exists, NetBackup runs it passing three parameters on [LINK:
> mailto:-@REM] -@REM - the command line:
>
>
> Is this normal? Any help would be appreciated.
>
>
> Thank you,
>
> Jason
|
|
|