Veritas-bu

[Veritas-bu] writing to a tape

2003-05-21 12:17:25
Subject: [Veritas-bu] writing to a tape
From: scott.kendall AT abbott DOT com (scott.kendall AT abbott DOT com)
Date: Wed, 21 May 2003 11:17:25 -0500
This is a multipart message in MIME format.
--=_alternative 00597ECA86256D2D_=
Content-Type: text/plain; charset="us-ascii"

there are a few reasons something like this would happen and you might do 
something different to fix it, depending on what you're actually looking 
for and what else is going on when these two jobs run.

- the data could be using a different retention level.  tell NetBackup to 
mix retention levels (not recommended. make sure you know the 
ramifications) or change the retention levels to be the same.
- the jobs could be queueing at the same time and there are available 
drives, so it runs.  use multiplexing to put them on the same drive at the 
same time or point them at a storage unit that is limited to only one 
drive.

my advice... read the NetBackup Troubleshooting Guide to get a better 
understanding of how it actually works under the covers and then you'll 
know why it's doing this.  I think in many cases, the knowledge that can 
be gained from this manual is the difference between you controlling 
NetBackup or NetBackup controlling you.


- Scott





"Sen" <discussion.groups AT gmx DOT net>
Sent by: veritas-bu-admin AT mailman.eng.auburn DOT edu
05/21/2003 10:30 AM
Please respond to "Sen"

 
        To:     "netbackup-l" <netbackup-l AT yahoogroups DOT com>, "nbu-lserv" 
<nbu-lserv AT dsihost-srv01 DOT com>, <veritas-bu AT mailman.eng.auburn DOT edu>
        cc: 
        Subject:        [Veritas-bu] writing to a tape


hi,
i noticed that NBU uses 2 tapes to backup data which is about 10GB in 
size.
which wastes alot of my tapes.
how do i restrict NBU to fill up a tape before using the next tape?
thanks


_______________________________________________
Veritas-bu maillist  -  Veritas-bu AT mailman.eng.auburn DOT edu
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu



--=_alternative 00597ECA86256D2D_=
Content-Type: text/html; charset="us-ascii"


<br><font size=2 face="Arial">there are a few reasons something like this would 
happen and you might do something different to fix it, depending on what you're 
actually looking for and what else is going on when these two jobs run.</font>
<br>
<br><font size=2 face="Arial">- the data could be using a different retention 
level. &nbsp;tell NetBackup to mix retention levels (not recommended. make sure 
you know the ramifications) or change the retention levels to be the 
same.</font>
<br><font size=2 face="Arial">- the jobs could be queueing at the same time and 
there are available drives, so it runs. &nbsp;use multiplexing to put them on 
the same drive at the same time or point them at a storage unit that is limited 
to only one drive.</font>
<br>
<br><font size=2 face="Arial">my advice... read the NetBackup Troubleshooting 
Guide to get a better understanding of how it actually works under the covers 
and then you'll know why it's doing this. &nbsp;I think in many cases, the 
knowledge that can be gained from this manual is the difference between you 
controlling NetBackup or NetBackup controlling you.</font>
<br>
<br>
<br><font size=2 face="Arial">- Scott</font>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td>
<td><font size=1 face="sans-serif"><b>&quot;Sen&quot; &lt;discussion.groups AT 
gmx DOT net&gt;</b></font>
<br><font size=1 face="sans-serif">Sent by: veritas-bu-admin AT 
mailman.eng.auburn DOT edu</font>
<p><font size=1 face="sans-serif">05/21/2003 10:30 AM</font>
<br><font size=1 face="sans-serif">Please respond to &quot;Sen&quot;</font>
<br>
<td><font size=1 face="Arial">&nbsp; &nbsp; &nbsp; &nbsp; </font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; To: &nbsp; 
&nbsp; &nbsp; &nbsp;&quot;netbackup-l&quot; &lt;netbackup-l AT yahoogroups DOT 
com&gt;, &quot;nbu-lserv&quot; &lt;nbu-lserv AT dsihost-srv01 DOT com&gt;, 
&lt;veritas-bu AT mailman.eng.auburn DOT edu&gt;</font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; cc: &nbsp; 
&nbsp; &nbsp; &nbsp;</font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; Subject: &nbsp; 
&nbsp; &nbsp; &nbsp;[Veritas-bu] writing to a tape</font></table>
<br>
<br>
<br><font size=2 face="Courier New">hi,<br>
i noticed that NBU uses 2 tapes to backup data which is about 10GB in size.<br>
which wastes alot of my tapes.<br>
how do i restrict NBU to fill up a tape before using the next tape?<br>
thanks<br>
<br>
<br>
_______________________________________________<br>
Veritas-bu maillist &nbsp;- &nbsp;Veritas-bu AT mailman.eng.auburn DOT edu<br>
http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu<br>
</font>
<br>
<br>
--=_alternative 00597ECA86256D2D_=--

<Prev in Thread] Current Thread [Next in Thread>