This is a multipart message in MIME format.
--=_alternative 005BB81487256C1D_=
Content-Type: text/plain; charset="us-ascii"
Re: the below message.
How are you using sgscan?
sgscan tape ???
or just
sgscan
To see the library you can do:
sgscan changer
To get all the info, you can do:
tpconfig -d
Hello All,
I am trying to get the following configuration to work..
I have an l700 attached to a switch that is attached to
a emulex card in a host running solaris.
I am running netbackup 3.4 and i can see the drives in /dev/rmt
and sgscan see the drives fine.
unfortunately i cannot see the library in sgscan
i can see the library in the lputil emulex configuration tool
and have given a target id of 99.
i have edited the sg.links fiel and added the following
type=ddi_pseudo;name=sg;addr=63,0; sg/c\N0t99l0
type=ddi_pseudo;name=sg;addr=63,1; sg/c\N0t99l1
and also edited the sg.conf file
name="sg" class="scsi" target=99 lun=0;
name="sg" class="scsi" target=99 lun=1;
and then did a boot -r , i am still unable to see the
device in sgscan and in /dev/sg the device does not show up..
anyone run into this issue
-H
--=_alternative 005BB81487256C1D_=
Content-Type: text/html; charset="us-ascii"
<br><font size=2 face="sans-serif">Re: the below message.</font>
<br>
<br><font size=2 face="sans-serif">How are you using sgscan?</font>
<br><font size=2 face="sans-serif"> sgscan tape
???</font>
<br><font size=2 face="sans-serif">
or just</font>
<br><font size=2 face="sans-serif"> sgscan</font>
<br>
<br><font size=2 face="sans-serif">To see the library you can do:</font>
<br><font size=2 face="sans-serif"> sgscan
changer</font>
<br>
<br><font size=2 face="sans-serif">To get all the info, you can do:</font>
<br><font size=2 face="sans-serif"> tpconfig
-d</font>
<br>
<br>
<br>
<br><font size=3 face="Courier New">Hello All,<br>
<br>
I am trying to get the following configuration to work..<br>
<br>
I have an l700 attached to a switch that is attached to<br>
a emulex card in a host running solaris.<br>
<br>
I am running netbackup 3.4 and i can see the drives in /dev/rmt<br>
and sgscan see the drives fine.<br>
<br>
unfortunately i cannot see the library in sgscan<br>
i can see the library in the lputil emulex configuration tool<br>
and have given a target id of 99.<br>
<br>
i have edited the sg.links fiel and added the following<br>
type=ddi_pseudo;name=sg;addr=63,0; sg/c\N0t99l0<br>
type=ddi_pseudo;name=sg;addr=63,1; sg/c\N0t99l1<br>
<br>
<br>
and also edited the sg.conf file<br>
<br>
name="sg" class="scsi" target=99 lun=0;<br>
name="sg" class="scsi" target=99 lun=1;<br>
<br>
<br>
<br>
and then did a boot -r , i am still unable to see the<br>
device in sgscan and in /dev/sg the device does not show up..<br>
<br>
anyone run into this issue<br>
<br>
<br>
-H<br>
<br>
</font>
--=_alternative 005BB81487256C1D_=--
|
