Re: [Networker] NMM 2.4 sp1 and Exchange 2013 sp3
2013-07-19 09:20:52
Ahh - my mistake - we're probably not running SP3 on our exchange server as I
don't admin it , will have to check into what level we're at and warn the mail
admin about this .... Thanks for the update Michael.
From: Jones, Michael (BRS) [mailto:michael.jones2 AT emc DOT com]
Sent: Thursday, July 18, 2013 4:24 PM
To: EMC NetWorker discussion; Goslin, Paul
Subject: RE: NMM 2.4 sp1 and Exchange 2013 sp3
The NetWorker Software Compatibility Guide (SCG) has the details:
The NetWorker 8.1 release, with NMM 3.0, has full support for Exchange Server
2013 and Exchange Server 2010 SP3 on Windows Server 2012.
-----Original Message-----
From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU] On
Behalf Of Goslin, Paul
Sent: Thursday, July 18, 2013 12:10 PM
To: NETWORKER AT LISTSERV.TEMPLE DOT EDU<mailto:NETWORKER AT LISTSERV.TEMPLE
DOT EDU>
Subject: Re: [Networker] NMM 2.4 sp1 and Exchange 2013 sp3
Hi David,
It works.
We are running such a setup - our server is 7.6.4 backing up an Exchange 2010
server using nmm24.build375 ...
We Have tested restores also and they work...
Mailbox / folder restores require the backup be written to / and the restore to
be read from an AFT device (we're using disk). We can only keep the past 3 days
on disk due to space constraints, then they are staged off to tape after 68
hours...
Paul
-----Original Message-----
From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU] On
Behalf Of Browning, David
Sent: Thursday, July 18, 2013 2:43 PM
To: NETWORKER AT LISTSERV.TEMPLE DOT EDU<mailto:NETWORKER AT LISTSERV.TEMPLE
DOT EDU>
Subject: Re: [Networker] NMM 2.4 sp1 and Exchange 2013 sp3
I apologize, it is Exchange 2010 SP3, not Exchange 2013.
David M. Browning Jr.
IT Project Coordinator Enterprise Backups and Help Desk
http://www.lsuhsc.edu/ithelpdesk
Twitter: @LSUHSCNO_IT
-----Original Message-----
From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU] On
Behalf Of Browning, David
Sent: Thursday, July 18, 2013 1:38 PM
To: NETWORKER AT LISTSERV.TEMPLE DOT EDU<mailto:NETWORKER AT LISTSERV.TEMPLE
DOT EDU>
Subject: [Networker] NMM 2.4 sp1 and Exchange 2013 sp3
Our Exchange administrators are in the process of upgrading our Exchange 2013
servers to SP3, and we have some questions. Right now, our backup server is
running 7.6.2.7, with a planned upgrade to 8.0.sp2 in September. In order to
run NMM2.4sp1, according to the EMC web site, we must have the Exchange client
on NW 8.0sp1 (or higher).
We are concerned about the backup server running 7.6.2.7, and the client
running 8.0sp2, and NMM 2.4sp1.
Is anyone else running this configuration out there? Any issues?
Thanks.
David M. Browning Jr.
IT Project Coordinator Enterprise Backups and Help Desk
http://www.lsuhsc.edu/ithelpdesk
Twitter: @LSUHSCNO_IT
|
|
|