Weird... 
I'm running a 7.6 Console and 'Volume' is a valid column option on the
'Save Sessions' tab for me ... 

-----Original Message-----
From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU] On
Behalf Of George Sinclair
Sent: Monday, October 01, 2012 5:48 PM
To: NETWORKER AT LISTSERV.TEMPLE DOT EDU
Subject: Re: [Networker] How can I see both volumes and save sets in
nmc?

On 2012-10-01 17:42, Bowersock, Bryan wrote:
> I am running Networker 8.0.0.1 and that is new to the NMC.  I'm
guessing you are on an earlier version (7.6.x)...
Correct. Thanks.
> -Bryan
>
> -----Original Message-----
> From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU] 
> On Behalf Of George Sinclair
> Sent: Monday, October 01, 2012 5:21 PM
> To: NETWORKER AT LISTSERV.TEMPLE DOT EDU
> Subject: Re: [Networker] How can I see both volumes and save sets in
nmc?
>
> OK, Duh! I have it now, guys. Sheesh! Thanks to Bingo and Bryan. That 
> was too obvious. Good grief, Charlie Brown! :-[
>
> I also see that I can adjust the order that the column headings appear
in using the up and down arrows in the list. Nice. That was my next
question.
>
> Bryan, I must be missing something obvious, but I don't see the 'Add
Columns' option, only "Remove This Column",  "Choose Table Columns...",
"Print... Ctrl-P" and Export.
>
> George
>
> On 2012-10-01 16:30, Bowersock, Bryan wrote:
>> Right-click in the Save Sessions tab on one of the column headings,
choose Add Columns>>>   Volume.  Or you can "Choose Table Columns..."
and click the checkbox for "Volume".
>>
>>
>>
>> Bryan Bowersock
>> Storage Administrator - Tampa, FL
>>
>>
>>
>> -----Original Message-----
>> From: EMC NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU]
>> On Behalf Of George Sinclair
>> Sent: Monday, October 01, 2012 4:07 PM
>> To: NETWORKER AT LISTSERV.TEMPLE DOT EDU
>> Subject: Re: [Networker] How can I see both volumes and save sets in
nmc?
>>
>> On 2012-10-01 15:34, bingo wrote:
>>> Just go to the 'Save Sessions' tab and click the headline. Then
select the appropriate columns.
>>> That's it.
>> Maybe I wasn't clear in my post. I'm under Monitoring, and I select
the 'Save Sessions' tab, but that doesn't show me the volume names.
Instead, it reports the following columns:
>>
>> Client Name, Save Set, Group, Level, Start Time, Duration, Device, 
>> Rate (KB/S), Size
>>
>> I also want to be able to see the affected volumes that are being
written to with their respective save sets. How can I report all of that
so I don't have to keep jumping back and forth between windows? Is there
anything in nmc to mimic the nwadmin Sessions window?
>>
>>> +-------------------------------------------------------------------
>>> +-
>>> +-
>>> +-
>>> |This was sent by carsten_reinfeld AT avus-cr DOT de via Backup Central.
>>> |Forward SPAM to abuse AT backupcentral DOT com.
>>> +-------------------------------------------------------------------
>>> +-
>>> +-
>>> +-
>> --
>> George Sinclair
>> Voice: (301) 713-3284 x210
>> - The preceding message is personal and does not reflect any official

>> or unofficial position of the United States Department of Commerce -
>> - Any opinions expressed in this message are NOT those of the US
Govt.
>> -
>>
>
> --
> George Sinclair
> Voice: (301) 713-3284 x210
> - The preceding message is personal and does not reflect any official 
> or unofficial position of the United States Department of Commerce -
> - Any opinions expressed in this message are NOT those of the US Govt.

> -
>


--
George Sinclair
Voice: (301) 713-3284 x210
- The preceding message is personal and does not reflect any official or
unofficial position of the United States Department of Commerce -
- Any opinions expressed in this message are NOT those of the US Govt. -