Re: [Networker] Networker 7.5 released
2008-12-30 17:07:57
Hi Stan,
Hope you are doing well. With regards to tuning nsrjobd for memory
utilization there is a knowledge base article on Powerlink which provides
details on this as well as a high level overview of nsrjobd, the nsrjobsdb, the
purging process etc. Additionally there is an RFE filed (LGTsc20017) to change
the default settings for the policies used to determine when purging occurs to
be more inline with what is recommeneded in the Upgrades Technical Note.
Hope no one minds but I'd like to make reference to the NetWorker Support By
Product Landing Page to point you to the Knowledge Base article regarding
nsrjobd to help raise awareness. This website has been up and running for some
time and it's purpose is to provide a central location of key NetWorker
Knowledge Base Articles, Whitepapers, Manuals, and Technical documents that are
available on Powerlink. This Landing Page is frequently updated with new
information, in particular the Installation and Upgrades section (up to and
including NetWorker 7.5).
There are two ways this website can be accessed:
>From Powerlink, go to the Support Menu -> Support By Product -> NetWorker
The direct link is https://support.emc.com/products/NetWorker.aspx
Both require Powerlink authentication to gain access.
In the Configuration Section within the Getting Started Tab you will see a link
entitled "Tuning jobsdb default settings" in the General Subsection. Clicking
on this link will take you to the article I was referencing
(http://solutions.emc.com/emcsolutionview.asp?id=esg93654).
I would also like to encourage anyone who visits this site to use the feedback
mechanism in the bottom right hand corner of every page to help us make this
site even better.
Thanks
Debbie
Debbie Dunn Mgr. Product Management Service Planning & SystemsEMC Global
Services Email: dunn_debbie AT emc DOT com
Check it out NetWorker Information Lives Here:
https://support.emc.com/products/NetWorker.asp
Spare me the grim litany of the "realist," give me the unrealistic aspirations
of the optimist any day.
-Colin Powell
> Date: Tue, 23 Dec 2008 08:36:24 -0500> From: stan AT TEMPLE DOT EDU> Subject:
> Re: [Networker] Networker 7.5 released> To: NETWORKER AT LISTSERV.TEMPLE DOT
> EDU> > > From: "Joe N. Wallace" <joe.n.wallace AT GMAIL DOT COM>> > Reply-To:
> EMC NetWorker discussion <NETWORKER AT LISTSERV.TEMPLE DOT EDU>, "Joe N.> >
> Wallace" <joe.n.wallace AT GMAIL DOT COM>> > Date: Tue, 23 Dec 2008 07:17:42
> +0000> > To: <NETWORKER AT LISTSERV.TEMPLE DOT EDU>> > Subject: Re:
> [Networker] Networker 7.5 released> > > > I was trying to find some product
> information / release notes for the 7.5> > version, but I find none.> > > >
> Where are these new features listed?> > The release notes for NetWorker 7.5
> are on the first screen of the> documentation section of PowerLink.> > I will
> probably hold off for two or three months before installing 7.5 on my> two
> servers. One reason for this delay is the memory requirement. I am also> a
> little bit disappointed that more hasn't been done to optimize nsrjobd> (its
> a memory hog), and the release notes don't give any information on how> to
> configure a NetWorker server in such a way as to minimize nsrjobd's> memory
> utilization.> > To sign off this list, send email to listserv AT
> listserv.temple DOT edu and type "signoff networker" in the body of the
> email. Please write to networker-request AT listserv.temple DOT edu if you
> have any problems with this list. You can access the archives at
> http://listserv.temple.edu/archives/networker.html or> via RSS at
> http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER
To sign off this list, send email to listserv AT listserv.temple DOT edu and
type "signoff networker" in the body of the email. Please write to
networker-request AT listserv.temple DOT edu if you have any problems with this
list. You can access the archives at
http://listserv.temple.edu/archives/networker.html or
via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER
|
|
|