First off, let me say that I have been fighting with this since March
2005.
It has only gotten better since I had a upper level engineer get
involved. He ran a webex session and changed the way that the HBAs and
Scalar were mapped. I have 10 drives shared between 6 servers, so I
have 60 instances of tape drives that I have to reconfigure when there
is a problem. Use jbedit, it will save you a ton of time.
You need to make sure that your Scalar has the lastest firmware.
Have ADIC make sure that all your HBAs and Scalar mappings are correct.
Make sure you are restarting your Scalar correctly.
I still have issues, but they swap in groups instead of all over the
place.
Kathy Stewart
Rodale, Inc
Emmaus, PA
Kathy.stewart AT rodale DOT com
-----Original Message-----
From: Legato NetWorker discussion [mailto:NETWORKER AT LISTSERV.TEMPLE DOT EDU]
On Behalf Of Fazil Saiyed
Sent: Tuesday, March 07, 2006 10:46 AM
To: NETWORKER AT LISTSERV.TEMPLE DOT EDU
Subject: [Networker] JBCONFIG_i2K Problems
Hello,
I am having hard time configuring server (Windows 2003-64 bit-Dell PE
6850).
Windows keeps rearranging Drive order ( IBM-LTO2) after drivers are
loaded, i see that the Networker 7.2.1 does not like the drive order
which i create and i have problems with backups, recover ( even though
the tape required for restore are inventoried and avallable in the lib,
they are not being loaded automatically.
Is there better commands or utilities that can quiry drive order,
Jbconfig can run under. Need immediate Help our enviroment.
i2K-LTO2.
CDI Flag set to Not used.
Errors: Adic resource out of Sync.
H:\>inquire
Could not start a Removable Storage session (0x00000422).
[email protected]:HL-DT-STCDRW/DVD GCC4244B101|CD-ROM
[email protected]:ADIC Scalar i2000 300A|Autochanger (Jukebox)
S/N: ADIC203101904_LL0
ATNN:ADIC 203101904_L
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape0
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape1
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape6
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape7
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape2
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape3
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape4
[email protected]:IBM ULTRIUM-TD2 53Y2|Tape, \\.\Tape5
[email protected]:PE/PV 1x5 SCSI BP 1.0 |Processor
[email protected]: RAID DummyDevice 0000|Unknown Device Type
[email protected]:PERC LD 0 PERCRAID |Disk
[email protected]:PERC LD 1 PERCRAID |Disk
++++++++++++++++
D:\>jbconfig
1) Configure an AlphaStor/SmartMedia Jukebox.
2) Configure an Autodetected SCSI Jukebox.
3) Configure an Autodetected NDMP SCSI Jukebox.
4) Configure an SJI Jukebox.
5) Configure an STL Silo.
6) Configure a Microsoft Removable Storage Jukebox.
What kind of Jukebox are you configuring? [1] 2 Installing 'Standard
SCSI Jukebox' jukebox - [email protected].
What name do you want to assign to this jukebox device? ADIC Turn
NetWorker auto-cleaning on (yes / no) [yes]? y The drives in this
jukebox cannot be auto-configured with the available information. You
will need to provide the path for the drives.
Is (any path of) any drive intended for NDMP use? (yes / no) [no] n Is
any drive going to have more than one path defined? (yes / no) [no] n
Please enter the device path information in one of the following
formats:
\\.\Tape0 --for local path or
host:device-path --for remote node or
host:drive-letter:directory path --for Windows disk file
Drive 1, element 256
Drive path ? \\.\Tape0
Drive 2, element 257
Drive path ? \\.\Tape1
Drive 3, element 258
Drive path ? \\.\Tape6
Drive 4, element 259
Drive path ? \\.\Tape7
Drive 5, element 260
Drive path ? \\.\Tape2
Drive 6, element 261
Drive path ? \\.\Tape3
Drive 7, element 262
Drive path ? \\.\Tape4
Drive 8, element 263
Drive path ? \\.\Tape5
Please select the appropriate drive type number:
1) 3480 20) 9490 39) LTO Ultrium-3
2) 3570 21) 9840 40) optical
3) 3590 22) 9840b 41) qic
4) 3592 23) 9840C 42) SAIT-1
5) 4890 24) 9940 43) SD3
6) 4mm 25) 9940B 44) sdlt
7) 4mm 12GB 26) adv_file 45) sdlt320
8) 4mm 20GB 27) dlt 46) sdlt600
9) 4mm 4GB 28) dlt1 47) SLR
10) 4mm 8GB 29) dlt7000 48) tkz90
11) 4mm DAT72 30) dlt8000 49) travan10
12) 8mm 31) dst (NT) 50) tz85
13) 8mm 20GB 32) dtf 51) tz86
14) 8mm 5GB 33) dtf2 52) tz87
15) 8mm AIT 34) file 53) tz88
16) 8mm AIT-2 35) himt 54) tz89
17) 8mm AIT-3 36) logical 55) tz90
18) 8mm AIT-4 37) LTO Ultrium 56) tzs20
19) 8mm Mammoth-2 38) LTO Ultrium-2 57) VXA
Enter the drive type of drive 1? 38
Are all the drives the same model? (yes / no) [yes] y
Jukebox has been added successfully
The following configuration options have been set:
> Jukebox description to the control port and model.
> Autochanger control port to the port at which we found it.
> Networker managed tape autocleaning on.
> Barcode reading to on.
> Volume labels that match the barcodes.
> Slot intended to hold cleaning cartridge to 102. Please insure
that a
cleaning cartridge is in that slot
> Number of times we will use a new cleaning cartridge to 50.
> Cleaning interval for the tape drives to 6 months.
You can review and change the characteristics of the autochanger and its
associated devices using nwadmin.
Would you like to configure another jukebox? (yes/no) [no]n
D:\>
To sign off this list, send email to listserv AT listserv.temple DOT edu and
type "signoff networker" in the body of the email. Please write to
networker-request AT listserv.temple DOT edu if you have any problems wit this
list. You can access the archives at
http://listserv.temple.edu/archives/networker.html or via RSS at
http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER
To sign off this list, send email to listserv AT listserv.temple DOT edu and
type "signoff networker" in the
body of the email. Please write to networker-request AT listserv.temple DOT edu
if you have any problems
wit this list. You can access the archives at
http://listserv.temple.edu/archives/networker.html or
via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER
|
