Re: Returning Volumes from Overflow
2006-10-31 12:08:05
Thanks for everyones assistance, I have been able to move the data of
the tape and return the volume to scratch.
Dan
-----Original Message-----
From: ADSM: Dist Stor Manager [mailto:ADSM-L AT VM.MARIST DOT EDU] On Behalf Of
John Monahan
Sent: Monday, October 30, 2006 7:02 PM
To: ADSM-L AT VM.MARIST DOT EDU
Subject: Re: [ADSM-L] Returning Volumes from Overflow
I assume you are using the "move media" command to check these volumes
out
of the library and update the overflow location.
If so, then you want to use the "move media" command first to move the
volumes from a mountablenotinlib state to a mountable state. Then you
can
check them in with the checkin command.
Here is the relevant section from the move media command when you want
to
check volumes back into the library:
MOUNTABLENotinlib
Specifies that storage pool volumes are to change from the
MOUNTABLENOTINLIB state back to the MOUNTABLEINLIB state. Volumes
in the MOUNTABLENOTINLIB state may contain valid data and are in
the overflow location.
For empty scratch volumes, the MOVE MEDIA command deletes the
volume records so that they can be used again.
For private volumes, the MOVE MEDIA command resets the volume
location to blank, changes the volumes's state to CHECKIN,
and changes the last update date to the current date.
For scratch volumes with data, the MOVE MEDIA command resets
the volume location to blank, changes the volumes's state to
CHECKIN, and changes the last update date to the current
date.
Note:
Volumes in the CHECKIN state may contain valid data and need
to be checked into the library.
______________________________
John Monahan
Consultant Infrastructure Solutions Group
Computech Resources, Inc., a Logicalis Company
Office: 952-833-0930 ext 109
Cell: 952-221-6938
http://www.computechresources.com
http://us.logicalis.com
Dan Cyr <dan.cyr AT COUNTY-LAMBTON.ON DOT CA>
Sent by: "ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>
10/30/2006 12:42 PM
Please respond to
"ADSM: Dist Stor Manager" <ADSM-L AT VM.MARIST DOT EDU>
To
ADSM-L AT VM.MARIST DOT EDU
cc
Subject
Returning Volumes from Overflow
I have been experimenting with using the Overflow location; I have been
able to remove the media successfully. I seem to be having problems
returning the media back into the library. We are running TSM 5.3.0 on
a Win2K3 platform using an IBM4560 SLX. I was able to bring the media
back to the library, however it is listed as private and I cannot change
to scratch. I get the following message when trying to update the
volume "ANR8443E UPDATE LIBVOLUME: Volume LAM004 in library IBM4560
cannot be assigned a status of SCRATCH." The other issue is that I
can't seem to remove the overflow location tag either, so when I am
querying what volumes are out I am getting incorrect responses.
Thank you
Dan Cyr
Network Specialist
Information Technology and Telecommunications Department
County of Lambton
Tel: (519) 845-0801 ext 347
E-mail dan.cyr AT county-lambton.on DOT ca
DISCLAIMER:
If you are not the intended recipient of this transmission, you are
hereby
notified that
any disclosure or other action taken in reliance on its contents is
strictly prohibited.
Please delete the information from your system and notify the sender
immediately. If you
receive this email in error contact the County of Lambton at 519 845
0801
extension 405 or
email itsupport AT county-lambton.on DOT ca.
DISCLAIMER:
If you are not the intended recipient of this transmission, you are hereby
notified that
any disclosure or other action taken in reliance on its contents is strictly
prohibited.
Please delete the information from your system and notify the sender
immediately. If you
receive this email in error contact the County of Lambton at 519 845 0801
extension 405 or
email itsupport AT county-lambton.on DOT ca.
|
|
|