The user who's password is set to perform the backups is the system Admin,
highest rights and all rights.
And when you say delete ADSM files do you mean did I uninstall fully and
only then upgrade ?
The answer to this is no, I upgraded over existing files. But I did the same
on all servers.
Mike
> -----Original Message-----
> From: Larry Way [SMTP:Larry.Way AT TRW DOT COM]
> Sent: ? ??? 27 2000 17:29
> To: ADSM-L AT VM.MARIST DOT EDU
> Subject: Re: Netware backup problems on some servers running
> ADSMclient V er 3 , Release 1, Level 0.8
>
> When you upgraded these clients did you delete ADSM files from Netware
> before installing the new ADSM client ? I'm assuming you have proper
> permissions to backup these containers within Netware ?
>
> Larry Way
> SL09/100D
> 408-743-4242 Voice
> 408-690-2327 Cell
> 408-743-4201 Fax
>
> >>> admin AT IAA.GOV DOT IL 03/27/00 05:58AM >>>
> Mark,
>
> As you requested The DSM.OPT is as follows :
>
> It's the same on all servers excepting the node name.
>
> Mike
>
> ==========================================================================
> ==
> ==================
>
> ************************************************************************
> * ADSTAR Distributed Storage Manager
> *
> * Sample client options file for ADSM Novell NetWare client
> ************************************************************************
>
> *********************************************************************
> * Copy DSM.SMP (this file) to DSM.OPT.
> *
> * To specify the communication method used between the client node
> * and server. Select one of the following communication methods
> * by removing the '*'. Fill in NODENAME and this will represent a
> * minimum set of options to get started.
> *
> * You may also exclude some operating system files. A recommended
> * list is at the bottom of this file. These files typically are
> * system level files that, even if backed up, could not be properly
> * restored. If they are restored, they could corrupt the operation
> * of the system. If you decide to use the list, simply remove the
> * '*'.
> *
> * (for the communication method values, you may have to
> * contact your system administrator)
> *********************************************************************
>
> * Communications settings
> * -------------------------------------------------------
>
> * Setting Options for the SNA LU 6.2 Communication Method
> * -------------------------------------------------------
> * COMMMETHOD SNAlu6.2
> * SYMBOLICDESTINATION server
>
>
> * Setting Options for the TCP/IP Communication Method
> * -------------------------------------------------------
> *
> COMMMETHOD TCPip
> TCPSERVERADDRESS 172.17.253.21
> TCPPORT 1500
>
>
> * Setting Options for the IPX/SPX Communication Method
> * -------------------------------------------------------
> *
> * COMMMETHOD IPXSPX
> * IPXSERVERADDRESS ipx_address
> * IPXSOCKET ipx_socket
>
>
> * Setting Options for the PWSCS Communication Method
> * -------------------------------------------------------
> * COMMMETHOD PWScs
> * SYMBOLICDESTINATION server
> *
> * COMMMETHOD PWSCS
> * TPNAME server
> * PARTNERLUNAME target_lu
> * CPICMODENAME session_of_target_lu
> * CPICBUFFERSIZE 15
>
>
> * Setting Nodename
> * -------------------------------------------------------
>
> NODENAME GIS
>
>
> *
> * Recommended exclude list for NetWare
> * -------------------------------------------------------
> *
> * NetWare 3.x specific - use the INCR BINDERY or SEL BINDERY
> * command to backup the bindery; exclude the real bindery
> * files:
> * -------------------------------------------------------
> * EXCLUDE sys:\system\net$obj.sys
> * EXCLUDE sys:\system\net$prop.sys
> * EXCLUDE sys:\system\net$val.sys
>
> *
> * NetWare 4.x specific - NDS leaf objects can be included/
> * excluded; container objects are not affected. This example
> * shows how to include only objects in container
> * .OU=Development.O=ADSM
> * ---------------------------------------------------------
> * EXCLUDE directory:/.O=ADSM/.../*
> * INCLUDE directory:/.O=ADSM/.OU=Development.O=ADSM/.../*
> INCLUDE directory:/.O=IAA/.../*
> *
> * NetWare general excludes
> * ---------------------------------------------------------
> EXCLUDE sys:\system\secaudit.log
> EXCLUDE sys:\system\events.log
> EXCLUDE sys:\system\system.log
> EXCLUDE sys:\system\btrieve.trn
> EXCLUDE sys:\system\tsa\tsa$temp.*
> EXCLUDE sys:\system\sys$log.err
> EXCLUDE sys:\vol$log.err
> EXCLUDE sys:\tts$log.err
> EXCLUDE SYS:\QUEUES\*\*.SRV
> EXCLUDE SYS:\QUEUES\*\*.SYS
>
>
> * NetWare Screen option
> * ---------------------------------------------------------------
> * The following option instructs the NetWare client to destroy
> * the ADSM screen when quitting the dsmc program.
> *
> NWWAIT NO
>
> * NetWare user ID and password option
> * --------------------------------------------------------------
> * The following option specifies a user ID and password to connect
> * to a local or remote NetWare resource (server or NDS tree). The
> * user ID must have NetWare supervisory equivalence. Use this
> * option for each resource which will be managed by ADSM.
> *
> * If this option is not specified in the client options file, ADSM
> * will check for a user ID and password in an encrypted file (if
> * NWPWFILE is set to YES). If a correct user ID and password
> * is not found in a file (or NWPWFILE is set to NO), ADSM will prompt
> * for a user ID and password when a backup or archive operation
> * is initiated.
> *
> * NWUSER server_1_name\user:password
> * NWUSER server_2_name\user:password
> * NWUSER nds_tree_name\user:password
> * NWUSER NS_IAA_GIS\admin:reshet
>
> * NetWare user ID and password file
> * --------------------------------------------------------------
> * The following option specifies that the user ID and password used
> * to connect to a NetWare resource (server or NDS tree) will be stored
> * in an encrypted file in the installation directory after the intiial
> * prompt. An encrypted file will be created for each resource with the
> * extension .PWD
> *
> PASSWORDACCESS GENERATE
> NWPWFILE YES
>
> * Silencing screen output
> * -----------------------------------------------------------------
> * Use the QUIET option to keep messages from being displayed on the
> * NetWare console and the schedule log file. This option will enhance
> * the performance during scheduled backups.
> *
> * Note that by using this option, schedule event windows, schedule
> * statistics and errors during schedule processing will still be
> * written to the schedule log file.
> *
> * If this option is not specified, the default VERBOSE will be taken.
> *
> * QUIET
>
>
> * Communication Paramaters
> *--------------------------------------------------------------------
> TCPBUFFSIZE 31
> TCPWINDOWSIZE 48
> TXNBYTELIMIT 2048
>
> SCHEDLOGname V_VOL1:/ADSMLOG/dsmsched.log
> ERRORLOGname V_VOL1:/ADSMLOG/error.log
> SCHEDLOGretention 6 D
>
> SCROLLPrompt YES
> SCROLLLines 20
>
> COMPression NO
>
> LARGECOMMBUFFERS YES
> MEMORYEFFICIENTBACKUP NO
>
> ==========================================================================
> ==
> ==================
>
> > -----Original Message-----
> > From: Remeta, Mark [SMTP:MRemeta AT SELIGMANDATA DOT COM]
> > Sent: ? ??? 27 2000 15:18
> > To: ADSM-L AT VM.MARIST DOT EDU
> > Subject: Re: Netware backup problems on some servers running ADSM
> > client V er 3 , Release 1, Level 0.8
> >
> > Mike, why don't you post your dsm.opt file too.
> >
> > thanks,
> > Mark
> >
> >
> > -----Original Message-----
> > From: Mike Glassman - Admin [mailto:admin AT IAA.GOV DOT IL]
> > Sent: Sunday, March 26, 2000 5:17 AM
> > To: ADSM-L AT VM.MARIST DOT EDU
> > Subject: Netware backup problems on some servers running ADSM client Ver
> > 3 , Release 1, Level 0.8
> >
> >
> > Hi all,
> >
> > Sending this a second time, as I didn't get and replies on the first.
> >
> > I am having some trouble on some of my Netware 5.0 servers when
> attempting
> > to run a Scheduled backup of the server with the above client.
> >
> > When running the scheduled backup, I end up with an error 4, and when
> > looking in the logs, I see that I have no rights to backup the server
> > specific info, or the volumes.
> >
> > The very strange thing is that if I run a manuall INC command using :
> >
> > Load DSMC INC -SUB=YES SYS: V_VOL1: V_VOL2:
> >
> > on the same server, I manage to backup fine with no errors at all.
> >
> > The command that I use to run the Scheduled backup is a simple :
> >
> > Load DSMC SCHED -pass=gis
> >
> > All servers also run the web based NLM - DSMCAD.NLM which is loaded one
> > line
> > after the SCHED command line.
> >
> > All servers load TSA500 and TSANDS prior to running the schedule command
> > for
> > backup.
> >
> > All servers have 128MB RAM.
> >
> > This started about 2 weeks ago, and occurs on 5 out of 13 servers. All
> > servers run the same SCHED command line, (but with different -pass=
> names
> > of
> > course), and all have the same scheduler set up at 10 minute intervals.
> >
> > Our ADSM server is an AS400 running Server Version 3, Release 1, Level
> > 1.7.
> >
> > I would appreciate any and all assistance with this as I am at wits end
> > already.
> >
> > The errors that appear in the log ar as follows :
> >
> > 03/19/2000 14:49:16 --- SCHEDULEREC QUERY BEGIN
> > 03/19/2000 14:49:16 --- SCHEDULEREC QUERY END
> > 03/19/2000 14:49:16 Next operation scheduled:
> > 03/19/2000 14:49:16
> > ------------------------------------------------------------
> > 03/19/2000 14:49:16 Schedule Name: GIS
> > 03/19/2000 14:49:16 Action: Incremental
> > 03/19/2000 14:49:16 Objects:
> > 03/19/2000 14:49:16 Options:
> > 03/19/2000 14:49:16 Server Window Start: 21:45:00 on 03/19/2000
> > 03/19/2000 14:49:16
> > ------------------------------------------------------------
> > 03/19/2000 14:49:16 Command will be executed in 7 hours and 9 minutes.
> > 03/19/2000 14:49:16
> > Time remaining until execution:
> > Executing scheduled command now.
> > 03/19/2000 21:58:16 Node Name: GIS
> > 03/19/2000 21:58:17 Session established with server ADSM_SYSTEM2: AS400
> > 03/19/2000 21:58:17 Server Version 3, Release 1, Level 1.7
> > 03/19/2000 21:58:17 Server date/time: 03/19/2000 21:56:33 Last
> access:
> > 03/19/2000 14:47:33
> >
> > 03/19/2000 21:58:17 --- SCHEDULEREC OBJECT BEGIN GIS 03/19/2000 21:45:00
> > 03/19/2000 21:58:26
> > Connecting to a NetWare File System (NS_IAA_GIS).
> >
> > 03/19/2000 21:58:26
> > Connected to NS_IAA_GIS.
> >
> > 03/19/2000 21:58:35
> > Connecting to a Novell Directory (T_IAA).
> >
> > 03/19/2000 21:58:35
> > Connected to T_IAA.
> >
> > 03/19/2000 21:58:35 Incremental backup of volume 'NS_IAA_GIS\SERVER
> > SPECIFIC
> > INFO'
> > 03/19/2000 21:58:35 Normal File--> 1,048,576 Server Specific
> > Info/Server Specific Info ** Unsuccessful **
> > 03/19/2000 21:58:36 ANS1228E Sending of object 'Server Specific
> > Info/Server
> > Specific Info' failed
> > 03/19/2000 21:58:36 ANS4007E Error processing 'Server Specific
> Info/Server
> > Specific Info': access to the object is denied
> > 03/19/2000 21:58:36 ANS1802E Incremental backup of 'NS_IAA_GIS\SERVER
> > SPECIFIC INFO' finished with 1 failure
> >
> > 03/19/2000 21:58:36 Incremental backup of volume 'NS_IAA_GIS\SYS:'
> > 03/19/2000 21:58:36 ANS1087E Access to the specified file or directory
> is
> > denied
> > 03/19/2000 21:58:36 Incremental backup of volume 'NS_IAA_GIS\V_VOL1:'
> > 03/19/2000 21:58:36 ANS1087E Access to the specified file or directory
> is
> > denied
> > 03/19/2000 21:58:36 Incremental backup of volume 'NS_IAA_GIS\V_VOL2:'
> > 03/19/2000 21:58:36 ANS1087E Access to the specified file or directory
> is
> > denied
> > 03/19/2000 21:58:36 --- SCHEDULEREC OBJECT END GIS 03/19/2000 21:45:00
> > 03/19/2000 21:58:36 --- SCHEDULEREC STATUS BEGIN GIS 03/19/2000 21:45:00
> > 03/19/2000 21:58:36 Total number of objects inspected: 1
> > 03/19/2000 21:58:36 Total number of objects backed up: 0
> > 03/19/2000 21:58:36 Total number of objects updated: 0
> > 03/19/2000 21:58:36 Total number of objects rebound: 0
> > 03/19/2000 21:58:36 Total number of objects deleted: 0
> > 03/19/2000 21:58:36 Total number of objects failed: 1
> > 03/19/2000 21:58:36 Total number of bytes transferred: 0
> > 03/19/2000 21:58:36 Data transfer time: 0.00 sec
> > 03/19/2000 21:58:36 Network data transfer rate: 0.00 KB/sec
> > 03/19/2000 21:58:36 Aggregate data transfer rate: 0.00 KB/sec
> > 03/19/2000 21:58:36 Objects compressed by: 0%
> > 03/19/2000 21:58:36 Elapsed processing time: 00:00:18
> > 03/19/2000 21:58:36 --- SCHEDULEREC STATUS END GIS 03/19/2000 21:45:00
> > 03/19/2000 21:58:36 ANS1512E Scheduled event 'GIS' failed. Return code
> =
> > 4.
> > 03/19/2000 21:58:36 Sending results for scheduled event 'GIS'.
> > 03/19/2000 21:58:36 Results sent to server for scheduled event 'GIS'.
> >
> > 03/19/2000 21:58:37 ANS1483I Schedule log pruning started.
> > 03/19/2000 21:58:37 Schedule Log Prune: 916 lines processed. 90 lines
> > pruned.
> > 03/19/2000 21:58:37 ANS1484I Schedule log pruning finished successfully.
> > 03/19/2000 21:58:37 Querying server for next scheduled event.
> > 03/19/2000 21:58:37 Node Name: GIS
> > 03/19/2000 21:58:37 Session established with server ADSM_SYSTEM2: AS400
> > 03/19/2000 21:58:37 Server Version 3, Release 1, Level 1.7
> > 03/19/2000 21:58:37 Server date/time: 03/19/2000 21:56:53 Last
> access:
> > 03/19/2000 21:56:33
> >
> >
> >
> > Mike Glassman
> > System & Security Admin
> > Israeli Airports Authority
> > Ben-Gurion Airport
> > http://www.ben-gurion-airport.co.il
> >
> > Tel : 972-3-9710785
> > Fax : 972-3-9710939
> > Email : admin AT iaa.gov DOT il
> >
> > Usage of this email address or any email address at iaa.gov.il for the
> > purpose of sales pitches, SPAM or any other such unwanted garbage, is
> > illegal, and any person, whether corporate or alone doing so, will be
> > prosecuted to the fullest possible extent.
|