Hi chris, and sorry because i forgot to tell you that my 3570 is
working under ... a 2944 Adaptec (fast wide diff) !!
Happy to know your config is now working.
Bye ! Chris
--- Christy WU <tfwu AT ELMCT DOT COM> a icrit:
> Dear all,
> Dear all,
>
> Thanks for all your help. I have solved the problem
> by replacing the IBM
> 4_B differential adapter to an Adaptec 2944 UW one.
> Amazingly it works
> perfectly once I plugged it in the system. Again my
> appreciation to all of
> your help.
>
> Regards,
> Christy WU
> ELM Computer Technologies Limited.
>
>
>
>
>
>
> "Robinson, Cris" <Cris.Robinson AT LibertyMutual DOT com>
> on 06/01/99 10:14:46 PM
>
> To: Christy Wu/TSD/ELM/HK, ADSM-L AT VM.MARIST DOT EDU
> cc:
> Subject: RE: I/O Error and SCSI Adapter Failure
> while writing data to tape
> cartridge
>
>
>
>
> Christy -
> Be sure that you are looking at the drives on the
> correct port when you
> define them in ADSM.
> Here is a good way to check:
> Go to the control panel, click on SCSi adapters.
> Click on the adapter that
> your library is connected to, for me it is an
> adaptec card,
> click on your library to get the properties and
> click in the settings tab.
> The port should be 01 based on your configuration
> define in ADSM
> of MT0.0.0.1 If the number is different in the
> settings tab make sure to
> update your drive to match it. I.E if the settings
> tab says
> 2 in the SCSI port field then update the drive to
> mt0.0.0.2.
>
>
> Let us know!
>
> Good luck -
> C
>
> __________________________________________________
> Cris Robinson
> Sr. Technical Analyst
> Enterprise Storage Management / ADSM
> Liberty Mutual Insurance
> Portsmouth, New Hampshire
> 603.431.8400.54837
> mailto:cris.robinson AT libertymutual DOT com
>
> Dilbert words of Wisdom:
> Accept that some days you're the pigeon,
> and some days you're the statue!
>
> -----Original Message-----
> From: Christy WU, T.F.
> [SMTP:tfwu AT ELMCT DOT COM]
> Sent: Saturday, May 29, 1999 5:55 AM
> To: ADSM-L AT VM.MARIST DOT EDU
> Subject: I/O Error and SCSI Adapter Failure
> while writing
> data to tape cartridge
>
> Hi folks,
>
> I need your help in solving the ADSM backup
> problem.
>
> Background story:
> To install ADSM 3.1 on NT Server 4.0 with
> Service Pack 4 running on
> IBM
> Netfinity 5500 and a Magstar MP 3570 attached
> to PCI SCSI-2
> Fast/Wide
> Differential adapter in Netfinity 5500.
> After installation finished and reboot, ADSM
> server started, device
> drive
> ADSMscsi started.
> Increase database, recovery log volume, disk
> storage pools.
> Under diagnostic found following items:
> TapePeripheral mt0.0.0.1
> MediumChangerPeripheral lb0.1.0.1
> TapePeripheral mt2.0.0.1
>
> Command used to define the library, dual
> drives, class and
> storagepool:
> >define library autolib libtype=scsi
> device=lb0.1.0.1
> >define drive autolib autodrive1
> device=my0.0.0.1 element=16
> >define drive autolib autodrive2
> device=my2.0.0.1 element=17
> >define devclass autoclass devtype=35700
> format=3570C
> library=autolib
> mountlimit=2
> >define stgpool autopool aotoclass
> maxscratch=100
> I use the wizard to label libray volume for
> both magazines and
> follwing
> command to check in the library volume
> >checkin libvolume autolib status=scratch
> search=yes
>
> Setting on the Magstar MP 3570:
> Library has been configured in Random mode and
> is running base
>
> All the above command run successfully. But
> problem occurs while I
> backup
> data on to the tape cartridge. The whole system
> was hung with the
> following
> error:
>
> ANR8302E I/O erroro on drive AUTODRIVE1
> <MT0.0.0.1>
> <OP=WRITE, CC=205, KEY=FF, ASC=FF, ASCQ=FF,
> SENSE=**NONE**
> Description=SCSI Adapter Failure>. Refer to
> Appendix B in the
> 'message'
> manual for recommended action.
>
> Message in the event viewer in NT:
>
> The description for Event ID (11) in source
> (AdsmScsi) could not be
> found.
> It contains the followinig insertion string(s):
> \Device\lb0.1.0.1
>
> The description for Event ID (11) in source
> (AdsmScsi) could not be
> found.
> It contains the followinig insertion string(s):
> \Device\mt0.0.0.1
>
>
> Action:
> I installed Magstar MP 3570 driver under NT
> tape device and backup
> successfully onto a tape cartridge on Magstar
> MP 3570 via NT's
> native
> backup. I guess it eliminates the possibility
> of adapter failure.
>
> Any clues? I tried to install service pack 3
> for NT 4.0 and also the
> fix 3.1.2.20 for ADSM V3R1, but no improvement has
> made. Have I miss a step
> during the installation? Or ADSM for NT simply
> doesn't work with Magstar MP
> 3570 and DLT 7337? Please advise.
>
> Regards,
> Christy WU
> ELM Computer Technologies Limited
>
___________________________________________________________
Do You Yahoo!?
Votre e-mail @yahoo.fr gratuit sur http://courrier.yahoo.fr
|